Campbell CR1000 - Ports and Status; Settings

To Next Page

To Previous Page

Section 8. Operation

8.8.5 Ports and Status

Read More See the appendix Registers.

Figure 124. C Terminals (Ports) Status

8.8.6 Settings

Figure 125. Settings

462

Main Page

Default Chapter1
- Control System1
- Table of Contents9
1 Introduction33
- Hello33
- Typography33
- Capturing Crbasic Code34
2 Cautionary Statements37
3 Initial Inspection39
4 System Quickstart41
- Data-Acquisition Systems - Quickstart41
- Sensors - Quickstart42
- Figure 1. Data-Acquisition System Components42
- Datalogger - Quickstart43
  - Wiring Panel - Quickstart43
- Power Supplies - Quickstart44
  - Figure 2. Wiring Panel44
  - Internal Battery - Quickstart45
- Data Retrieval and Telecommunications - Quickstart45
- Datalogger Support Software - Quickstart46
- Tutorial: Measuring a Thermocouple46
5 System Overview61
- Measurements - Overview62
- PLC Control - Overview74
- Datalogger - Overview75
- Datalogger Support Software - Overview95
6 Specifications97
7 Installation99
- Protection from Moisture - Details99
- Temperature Range99
- Enclosures99
- Power Supplies - Details100
- Switched Voltage Output - Details103
- Grounding105
- CR1000 Configuration - Details111
  - Configuration Tools111
  - CR1000 Configuration - Details117
- Crbasic Programming - Details122
- Programming Resource Library169
8 Operation303
- Measurements - Details303
- Measurement and Control Peripherals - Details366
- Memory370
- Data Retrieval and Telecommunications - Details391
- Pakbus® Communications - Details393
- Alternate Telecommunications - Details407
- Datalogger Support Software - Details450
- Keyboard Display - Details451
- Program and os File Compression Q and a463
- Table 126. Typical Gzip File Compression Results465
- Memory Cards and Record Numbers466
- Security - Details467
9 Maintenance - Details473
- Protection from Moisture - Details473
- Replacing the Internal Battery473
- Factory Calibration or Repair Procedure476
10 Troubleshooting479
- Troubleshooting - Essential Tools479
- Troubleshooting - Basic Procedure479
- Troubleshooting - Error Sources479
- Troubleshooting - Status Table481
- Programming481
- Troubleshooting - Operating Systems490
- Troubleshooting - Auto-Calibration Errors490
- Communications490
- Troubleshooting - Power Supplies494
- Terminal Mode501
  - Table 133. CR1000 Terminal Commands502
  - Serial Talk through and Comms Watch503
- Logs504
- Troubleshooting - Data Recovery504
11 Glossary507
- Terms507
- Table 135. Program Send Command524
- Concepts533
  - Accuracy, Precision, and Resolution533
12 Attributions535
Crbasic Programming Instructions537
- Program Declarations537
  - Variable Declarations & Modifiers538
  - Constant Declarations539
- Data-Table Declarations540
  - Data-Table Modifiers540
  - Data Destinations541
  - Processing for Output to Final-Data Memory542
    - Single-Source542
    - Multiple-Source544
- Single Execution at Compile544
- Program Control Instructions545
  - Common Program Controls545
  - Advanced Program Controls548
- Measurement Instructions550
  - Diagnostics550
  - Voltage551
  - Thermocouples551
  - Resistive-Bridge Measurements551
  - Excitation552
  - Pulse and Frequency553
  - Digital I/O554
    - Control554
    - Measurement555
  - Sensor Suppport - Instructions555
  - Specific Sensors556
    - Wireless Sensor Network558
  - Peripheral Device Support559
- PLC Control - Instructions562
- A.6 PLC Control — Instructions562
- Processing and Math Instructions563
  - Mathematical Operators563
  - Arithmetic Operators563
  - Bitwise Operations564
  - Compound-Assignment Operators565
  - Logical Operators565
  - Trigonometric Functions566
    - Intrinsic Trigonometric Functions566
    - Derived Trigonometric Functions568
  - Arithmetic Functions568
  - Integrated Processing570
  - Spatial Processing571
  - Other Functions572
    - Histograms573
- String Functions574
  - String Operations574
  - String Commands575
- Time Keeping - Instructions578
- A.9 Time Keeping — Instructions578
- Voice-Modem Instructions580
- Custom Menus - Instructions581
- A.11 Custom Menus — Instructions581
- Serial Input / Output583
- Peer-To-Peer Pakbus® Communications584
- Table 140. Asynchronous-Port Baud Rates588
- Variable Management589
- File Management589
- Data-Table Access and Management592
- TCP/IP - Instructions593
- A.17 TCP/IP — Instructions593
- Modem Control597
- Scada597
- Calibration Functions598
- Satellite Systems599
  - Argos599
  - Goes600
  - Omnisat601
  - Inmarsat-C601
- User-Defined Functions602
Status, Settings, and Data Table Information (Status/Settings/Dti)603
- Table 141. Status/Setting/Dti: Access Points603
Serial Port Pinouts633
- CS I/O Communication Port633
- Communication Port633
ASCII / ANSI Table637
FP2 Data Format641
Endianness643
Supporting Products Lists645
- Dataloggers - List645
- Measurement and Control Peripherals - Lists645
- Sensor-Input Modules Lists646
- PLC Control Modules - Lists648
- Sensors - Lists649
  - Wired-Sensor Types List650
  - Wireless-Network Sensors List650
- Data Retrieval and Telecommunication Peripherals - Lists651
- Data-Storage Devices - List653
- Datalogger Support Software - Lists654
- Power Supplies - Products657
- Enclosures - Products659
- Tripods, Towers, and Mounts Lists659
- Enclosures List660
- Table 233. Protection from Moisture — Products660
Index661

Campbell CR1000 - Ports and Status; Settings

Table of Contents

Related product manuals