Campbell CR1000 User Manual

Index
Polarity .................................................... 47
Polarity Reversal ..................................... 325
Polarized Sensor ..................................... 341
Polynomial — Thermocouple ................... 334
Port .......................................................... 78, 462
Power ...................................................... 48, 80, 97,
102, 103,
105
Power Budget .......................................... 101, 281,
282
Power Consumption ................................ 101
Powering Sensor ..................................... 85, 103
Power-up ................................................. 386
PPP ......................................................... 289, 593
PPP — Dial Response ............................ 603
PPP — Settings ...................................... 603
PPP — Username ................................... 603
PPP Information ...................................... 603
PPP Interface .......................................... 603
PPP IP Address ...................................... 518, 603
PPP Password ........................................ 603
Precision .................................................. 523, 533
Predefined Constant ............................... 138
Preserve Data ......................................... 127, 385
Preserve Settings .................................... 603
Pressure Transducer ............................... 321
Primer ...................................................... 41
Print Device ............................................. 524
Print Peripheral ....................................... 524
Priority ..................................................... 116, 151,
156
Probe ....................................................... 42, 649
Process Time .......................................... 603
Processing............................................... 563
Processing — Integrated ......................... 570
Processing — Output .............................. 145, 542
Processing — Spatial .............................. 571
Processing — Wind Vector ..................... 296
Processing Instructions ........................... 524
Processing Instructions — Output .......... 512
Processor ................................................ 97
Program ................................................... 86
Program — Alias ..................................... 138
Program — Array .................................... 135
Program — Compile Errors ..................... 481, 486,
488
Program — Constant .............................. 137
Program — Data Storage Processing Instruction 158
Program — Data Table ........................... 140
Program — Data Type ............................ 130
Program — DataInterval() Instruction ..... 144
Program — DataTable() Instruction ........ 143
Program — Declaration ........................... 129, 140,
537
Program — Dimension ............................ 134
Program — Documenting ........................ 126
Program — Execution ............................. 151
Program — Expression ........................... 160
Program — Field Calibration ................... 211
Program — Floating Point Arithmetic ...... 161
Program — Large .................................... 391
Program — Mathematical Operation ....... 161
Program — Measurement Instruction ..... 158
Program — Modbus ................................ 413
Program — Name in Parameter .............. 159
Program — Output Processing ............... 145
Program — Overrun ................................ 485, 603
Program — Parameter Type ................... 159
Program — Pipeline Mode ...................... 152
Program — Resource Library ................. 210
Program — Runtime Errors ..................... 481, 486,
488
Program — Scan ..................................... 154
Program — Scan Priority ......................... 156
Program — Sequential Mode .................. 153
Program — Slow Sequence .................... 155
Program — Structure .............................. 123
Program — Subroutine ............................ 147, 288
Program — SubScan .............................. 156
Program — Task Priority ......................... 151
Program — Timing .................................. 154
Program — Unit ....................................... 138
Program — Variable ................................ 129
Program Editor ........................................ 50
Program Errors ........................................ 486, 488,
603
Program Signature .................................. 603
Programming ........................................... 48, 55, 86,
126
Programming — Capturing Events ......... 169
Programming — Conditional Output ....... 170
Programming — Groundwater Pump Test ........... 171
Programming — Multiple Scans .............. 179
Programming — Running Average ......... 192
Programming — Scaling Array ................ 177
Protection ................................................ 93
Protocols Supported ................................ 97
PTemp ..................................................... 328
Pulse ........................................................ 62, 525
Pulse Count ............................................. 97, 349
Pulse Count Reset .................................. 177
Pulse Input .............................................. 69, 70
Pulse Input Expansion ............................. 367
Pulse Measurement ................................ 553
Pulse Sensor ........................................... 364
Pulse-Duration Modulation ...................... 79, 368
Pulse-Width Modulation .......................... 79, 368
PWM ........................................................ 79, 368
671

Campbell CR1000 Specifications

General

Power Requirements	9.6 to 16 VDC
Data Logger Operating System	CRBasic
Memory	4 MB
Analog Inputs	16 single-ended or 8 differential
Analog Input Resolution	13 bits
Analog Input Range	+/-2.5V
Digital I/O	8
Pulse Counters	2
Communication Ports	RS-232
Operating Temperature	-25°C to +50°C
Pulse Channels	4