Fujitsu PRIMERGY RX2520 M1 - Page 17

RX2520 M1 Upgrade and Maintenance Manual
Contents
12.6.2.2 Removing the ODD carrier . . . . . . . . . . . . . . . . . . 277
12.6.2.3 Removing the ODD . . . . . . . . . . . . . . . . . . . . . 278
12.6.2.4 Installing the ODD dummy module . . . . . . . . . . . . . . 280
12.6.2.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 281
12.6.3 Replacing an ODD . . . . . . . . . . . . . . . . . . . . . . . . 282
12.6.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 282
12.6.3.2 Removing the defective ODD . . . . . . . . . . . . . . . . 282
12.6.3.3 Installing the new ODD . . . . . . . . . . . . . . . . . . . . 282
12.6.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 282
12.7 Installing a RDX drive in 2.5-inch version . . . . . . . . . . 284
12.7.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 284
12.7.2 Installing a RDX drive in the cage . . . . . . . . . . . . . . . . 284
12.7.3 Installing the RDX drive . . . . . . . . . . . . . . . . . . . . . 286
12.7.4 Connecting the RDX drive . . . . . . . . . . . . . . . . . . . . 287
12.7.4.1 Connecting the RDX drive to the system board . . . . . . . 287
12.7.4.2 Connecting the RDX drive to the USB 3.0 interface card . . 287
12.7.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 289
12.8 Removing a RDX drive in 2.5-inch version . . . . . . . . . . 289
12.8.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 289
12.8.2 Removing the drive cage . . . . . . . . . . . . . . . . . . . . 289
12.8.3 Removing a RDX drive out of the cage . . . . . . . . . . . . . 291
12.8.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 293
12.9 Replacing the RDX drive in 2.5-inch version . . . . . . . . . 293
12.9.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 293
12.9.2 Removing the defective RDX drive . . . . . . . . . . . . . . . 294
12.9.3 Installing the new RDX drive . . . . . . . . . . . . . . . . . . . 294
12.9.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 294
12.10 Installing a LTO drive in 2.5-inch version . . . . . . . . . . . 294
12.10.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 295
12.10.2 Removing the drive cage . . . . . . . . . . . . . . . . . . . . 295
12.10.3 Removing the tape drive dummy module . . . . . . . . . . . . 296
12.10.4 Installing a LTO drive in the cage . . . . . . . . . . . . . . . . 297
12.10.5 Installing the LTO cage . . . . . . . . . . . . . . . . . . . . . 299
12.10.6 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 301
12.11 Removing an LTO drive in 2.5-inch version . . . . . . . . . 301
12.11.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 301
12.11.2 Removing the drive cage . . . . . . . . . . . . . . . . . . . . 302
12.11.3 Removing a LTO drive out of the cage . . . . . . . . . . . . . 303
12.11.4 Installing the tape drive dummy module . . . . . . . . . . . . . 305
12.11.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 307