EasyManuals Logo

Fujitsu PRIMERGY RX2520 M1 Upgrade And Maintenance Manual

Fujitsu PRIMERGY RX2520 M1
432 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #76 background imageLoading...
Page #76 background image
76 Upgrade and Maintenance Manual
RX2520 M1
Basic software procedures
5.2.1.2 Updating or recovering the iRMC
iRMC flash procedure
Ê Prepare a USB stick including the bootable iRMC firmware update image.
Ê Connect the USB stick to the USB port.
I Ensure that only the USB device with the iRMC firmware is connected
to the USB port. Remove all other USB devices temporarily.
Ê Restart the server.
Ê The system will detect the USB stick.
I If the BIOS cannot identify the USB stick, the pop-up message
Failed to boot for Emergency flash. Please Reset now.
will show up in the center of the screen.
Ê Choose one of the following options from the update tool menu to start the
iRMC update process:
Normal
Choose this option to update an existing system board.
Initial Choose this option if the system board has been replaced prior to the
iRMC update procedure. This option will perform all relevant flash
procedures in a row, including the iRMC firmware and bootloader.
V CAUTION!
Do not interrupt the iRMC upgrade process after it has started. If the
process is interrupted, the iRMC BIOS may be permanently
corrupted.
I If the iRMC does not work after flashing, disconnect the system from
the mains and reconnect it again.
Ê After completion of the flash process, remove the USB stick and restart the
server.
iRMC recovery procedure
Ê Prepare a USB stick including the bootable iRMC firmware update image.
Ê Ensure that the server has been shut down and disconnected from the
mains as described in section "Shutting down the server" on page 51.
Ê Connect the USB stick to the USB port.

Table of Contents

Other manuals for Fujitsu PRIMERGY RX2520 M1

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fujitsu PRIMERGY RX2520 M1 and is the answer not in the manual?

Fujitsu PRIMERGY RX2520 M1 Specifications

General IconGeneral
Bus typeQPI
SteppingC2
FSB ParityNo
Scalability2S
Processor codeSR0LM
Processor cache15 MB
Processor cores6
Processor modelE5-2430
System bus rate7.2 GT/s
Processor seriesIntel Xeon E5-2400
Processor socketLGA 1356 (Socket B2)
Processor threads12
Processor codenameSandy Bridge EN
Motherboard chipsetIntel C600
Processor frequency2.2 GHz
Processor cache typeSmart Cache
Processor lithography32 nm
Processor manufacturerIntel
Processor package size45 x 42.5 mm
Processor front side bus- MHz
Processor boost frequency2.7 GHz
Processor operating modes64-bit
Supported instruction setsAVX
Thermal Design Power (TDP)95 W
Compatible processor seriesIntel® Xeon®
Number of processors installed1
Maximum number of SMP processors2
Maximum number of PCI Express lanes24
Memory types supported by processorDDR3-SDRAM
Memory channels supported by processorTriple
Memory clock speeds supported by processor800, 1066, 1333 MHz
Memory bandwidth supported by processor (max)32 GB/s
Maximum internal memory supported by processor375 GB
Intelligent Platform Management Interface (IPMI) supportYes
HDD size- \
RAID levels0, 1
HDD interface-
Optical drive typeDVD-RW
Supported HDD sizes2.5, 3.5 \
Total storage capacity0 GB
Maximum storage capacity- TB
Number of HDDs installed0
Supported storage drive interfacesSAS, Serial ATA III
Internal memory8 GB
Memory clock speed1600 MHz
Maximum internal memory192 GB
LAN controllerIntel I210
Cabling technology10/100/1000Base-T(X)
Ethernet interface typeGigabit Ethernet
USB 2.0 ports quantity7
PCI Express slots version3.0
Operating system installedUnix
Compatible operating systemsHyper-V Server R2 2012\\r Windows Server 2012 R2 Datacenter\\r Windows Server 2012 R2 Standard\\r Windows Server 2012 R2 Essentials\\r Windows Storage Server 2012 R2 Standard\\r Hyper-V Server 2012\\r Windows Server 2012 Datacenter\\r Windows Server 2012 Standard\\r Windows Storage Server 2012 Standard\\r Hyper-V Server 2008 R2\\r Windows Server 2008 R2 Datacenter\\r Windows Server 2008 R2 Enterprise\\r Windows Server 2008 R2 Standard\\r Windows Server 2008 Datacenter\\r Windows Server 2008 Enterprise\\r Windows Server 2008 Standard\\r VMware vSphere 5.5 Embedded\\r VMware vSphere 5.5\\r VMware vSphere 5.0 Embedded\\r VMware vSphere 5.0\\r SUSE Linux Enterprise Server 12\\r SUSE Linux Enterprise Server 11\\r Red Hat Enterprise Linux 6\\r Red Hat Enterprise Linux 5\\r Red Hat Enterprise Linux 5 with XEN\\r Citrix XenServer
Processor ARK ID64616
Intel® Turbo Boost Technology1.0
Intel Identity Protection Technology version0.00
Chassis typeRack (2U)
Power consumption (typical)450 W
Power supply input frequency47 - 63 Hz
CertificationRoHS, WEEE, CB
Operating temperature (T-T)5 - 40 °C
Operating relative humidity (H-H)10 - 85 %
Weight and Dimensions IconWeight and Dimensions
Depth770 mm
Width482.6 mm
Height86.9 mm

Related product manuals