EasyManuals Logo

Fujitsu PRIMERGY RX2520 M1 Upgrade And Maintenance Manual

Fujitsu PRIMERGY RX2520 M1
432 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #88 background imageLoading...
Page #88 background image
88 Upgrade and Maintenance Manual
RX2520 M1
Basic software procedures
Ê Select the Advanced menu.
Ê Select the status menu of the desired component:
Processors: CPU Status
I This option is only available for multi-processor systems.
Memory: Memory Status
Expansion cards: PCI Status
Ê Reset replaced components to Enable.
Ê Save your changes and exit the BIOS.
I For detailed information on how to access the BIOS and modify settings,
refer to the corresponding BIOS Setup Utility reference manual.
5.2.10 Verifying the memory mode
If a memory module fails, the server will reboot and the defective module will be
disabled. As a result, the current operation mode (e.g. Mirrored Channel mode)
may no longer be available due to a lack of identical memory module pairs. In
this case, the operation mode will automatically revert to Independent Channel
Mode.
I For detailed information on memory operation modes available for your
server, refer to section "Memory sequence" on page 223.
After replacing the defective module(s) the memory operation mode is
automatically reset to its original state. It is recommended to verify that the
operation mode has been correctly.
Ê Enter the BIOS.
Ê Select the Advanced menu.
Ê Under Memory Status verify that none of the memory modules are marked as
Failed.
Ê Save your changes (if applicable) and exit the BIOS.
I For detailed information on how to access the BIOS and modify settings,
refer to the corresponding BIOS Setup Utility reference manual.

Table of Contents

Other manuals for Fujitsu PRIMERGY RX2520 M1

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fujitsu PRIMERGY RX2520 M1 and is the answer not in the manual?

Fujitsu PRIMERGY RX2520 M1 Specifications

General IconGeneral
Bus typeQPI
SteppingC2
FSB ParityNo
Scalability2S
Processor codeSR0LM
Processor cache15 MB
Processor cores6
Processor modelE5-2430
System bus rate7.2 GT/s
Processor seriesIntel Xeon E5-2400
Processor socketLGA 1356 (Socket B2)
Processor threads12
Processor codenameSandy Bridge EN
Motherboard chipsetIntel C600
Processor frequency2.2 GHz
Processor cache typeSmart Cache
Processor lithography32 nm
Processor manufacturerIntel
Processor package size45 x 42.5 mm
Processor front side bus- MHz
Processor boost frequency2.7 GHz
Processor operating modes64-bit
Supported instruction setsAVX
Thermal Design Power (TDP)95 W
Compatible processor seriesIntel® Xeon®
Number of processors installed1
Maximum number of SMP processors2
Maximum number of PCI Express lanes24
Memory types supported by processorDDR3-SDRAM
Memory channels supported by processorTriple
Memory clock speeds supported by processor800, 1066, 1333 MHz
Memory bandwidth supported by processor (max)32 GB/s
Maximum internal memory supported by processor375 GB
Intelligent Platform Management Interface (IPMI) supportYes
HDD size- \
RAID levels0, 1
HDD interface-
Optical drive typeDVD-RW
Supported HDD sizes2.5, 3.5 \
Total storage capacity0 GB
Maximum storage capacity- TB
Number of HDDs installed0
Supported storage drive interfacesSAS, Serial ATA III
Internal memory8 GB
Memory clock speed1600 MHz
Maximum internal memory192 GB
LAN controllerIntel I210
Cabling technology10/100/1000Base-T(X)
Ethernet interface typeGigabit Ethernet
USB 2.0 ports quantity7
PCI Express slots version3.0
Operating system installedUnix
Compatible operating systemsHyper-V Server R2 2012\\r Windows Server 2012 R2 Datacenter\\r Windows Server 2012 R2 Standard\\r Windows Server 2012 R2 Essentials\\r Windows Storage Server 2012 R2 Standard\\r Hyper-V Server 2012\\r Windows Server 2012 Datacenter\\r Windows Server 2012 Standard\\r Windows Storage Server 2012 Standard\\r Hyper-V Server 2008 R2\\r Windows Server 2008 R2 Datacenter\\r Windows Server 2008 R2 Enterprise\\r Windows Server 2008 R2 Standard\\r Windows Server 2008 Datacenter\\r Windows Server 2008 Enterprise\\r Windows Server 2008 Standard\\r VMware vSphere 5.5 Embedded\\r VMware vSphere 5.5\\r VMware vSphere 5.0 Embedded\\r VMware vSphere 5.0\\r SUSE Linux Enterprise Server 12\\r SUSE Linux Enterprise Server 11\\r Red Hat Enterprise Linux 6\\r Red Hat Enterprise Linux 5\\r Red Hat Enterprise Linux 5 with XEN\\r Citrix XenServer
Processor ARK ID64616
Intel® Turbo Boost Technology1.0
Intel Identity Protection Technology version0.00
Chassis typeRack (2U)
Power consumption (typical)450 W
Power supply input frequency47 - 63 Hz
CertificationRoHS, WEEE, CB
Operating temperature (T-T)5 - 40 °C
Operating relative humidity (H-H)10 - 85 %
Weight and Dimensions IconWeight and Dimensions
Depth770 mm
Width482.6 mm
Height86.9 mm

Related product manuals