1-4 F650 DIGITAL BAY CONTROLLER GEK-106310-AF
CHAPTER 1:
4.3.6 Fault report .............................................................................................................................4-71
4.3.7 Data logger.............................................................................................................................4-72
5 SETPOINTS 5.1 Overview ............................................................................................................5-1
5.1.1 Setpoint main menu..............................................................................................................5-1
5.2 Product setup....................................................................................................5-4
5.2.1 Communication settings .....................................................................................................5-4
5.2.1.1 Serial ports........................................................................................................................................... 5-4
5.2.1.2 Network (Ethernet) ........................................................................................................................... 5-4
5.2.1.3 MODBUS protocol............................................................................................................................. 5-7
5.2.1.4 DNP3 slave........................................................................................................................................... 5-7
5.2.1.5 IEC 60870-5-104............................................................................................................................... 5-9
5.2.1.6 SNTP......................................................................................................................................................5-10
5.2.1.7 Procome protocol settings.........................................................................................................5-11
5.2.1.8 IEC 870-5-103 protocol settings..............................................................................................5-11
5.2.1.9 PTP IEEE 1588 protocol settings ..............................................................................................5-12
5.2.1.10 Routing ................................................................................................................................................5-14
5.2.2 MODBUS user map settings............................................................................................5-16
5.2.3 Fault report settings ...........................................................................................................5-17
5.2.3.1 Fault report settings......................................................................................................................5-17
5.2.3.2 Fault report retrieval .....................................................................................................................5-18
5.2.4 Oscillography settings.......................................................................................................5-19
5.2.4.1 Oscillography settings .................................................................................................................5-19
5.2.4.2 Oscillography states .....................................................................................................................5-20
5.2.4.3 Oscillography file retrieval .........................................................................................................5-21
5.2.5 Data logger settings...........................................................................................................5-21
5.2.5.1 Data logger SETTINGS ..................................................................................................................5-21
5.2.5.2 Data logger associated states .................................................................................................5-22
5.2.5.3 Data logger file format and retrieval.....................................................................................5-22
5.2.6 Demand settings..................................................................................................................5-23
5.2.6.1 Metering values and settings....................................................................................................5-23
5.2.6.2 Demand calculation methods..................................................................................................5-24
5.2.6.3 Demand function measurements and states...................................................................5-27
5.2.7 Time Settings..........................................................................................................................5-28
5.3 System setup...................................................................................................5-31
5.3.1 General settings ...................................................................................................................5-31
5.3.2 Miscellaneous settings ......................................................................................................5-31
5.3.2.1 Out of service setting...................................................................................................................5-31
5.3.2.2 Local - remote block setting......................................................................................................5-34
5.3.3 FlexCurve settings ...............................................................................................................5-34
5.3.4 Breaker settings....................................................................................................................5-36
5.3.4.1 Breaker maintenance...................................................................................................................5-37
5.3.5 Switchgear settings............................................................................................................5-38
5.4 Protection elements.......................................................................................5-39
5.4.1 Available settings and setting groups........................................................................5-39
5.4.1.1 Firmware 7.2x and below ...........................................................................................................5-39
5.4.1.1.1 Single setting groups .......................................................................................................5-40
5.4.1.1.2 Three setting groups........................................................................................................5-40
5.4.1.2 Firmware 7.50 or above ..............................................................................................................5-43
5.4.1.2.1 Single setting group ........................................................................................................5-44
5.4.1.2.2 Multiple setting groups ...................................................................................................5-45
5.4.2 Inverse time curve characteristics ..............................................................................5-47
5.4.2.1 IEEE curves .......................................................................................................................................5-48
5.4.2.2 IEC curves..........................................................................................................................................5-49
5.4.2.3 IAC curves .........................................................................................................................................5-51
5.4.2.4 ANSI curves .......................................................................................................................................5-52
5.4.2.5 I2t curves...........................................................................................................................................5-54
5.4.2.6 Definite time curves.......................................................................................................................5-54
To Next Page
Loading...