1-6 F650 DIGITAL BAY CONTROLLER GEK-106310-AF
CHAPTER 1:
5.5.6 Pulse counters.................................................................................................................... 5-122
5.5.7 Analog comparators ....................................................................................................... 5-124
5.5.8 Maximum number of starts (66)................................................................................. 5-125
5.5.9 Digital counters.................................................................................................................. 5-127
5.5.10 Cold load pickup................................................................................................................ 5-129
5.5.11 60 CTS failure...................................................................................................................... 5-130
5.5.12 Second harmonic inhibit................................................................................................ 5-132
5.6 Inputs/outputs..............................................................................................5-135
5.6.1 Input/output placement................................................................................................ 5-135
5.6.2 Control settings for input/output............................................................................... 5-136
5.6.3 Inputs...................................................................................................................................... 5-138
5.6.4 Outputs.................................................................................................................................. 5-140
5.6.4.1 Output status signals.................................................................................................................5-140
5.6.5 Circuit supervision and contact seal-in circuits ................................................. 5-142
5.6.5.1 Digital inputs..................................................................................................................................5-142
5.6.5.2 With trip circuit supervision....................................................................................................5-142
5.6.5.3 Without supervision ...................................................................................................................5-144
5.6.5.4 With current supervision (with SEAL-IN) ...........................................................................5-144
5.6.5.5 With simple voltage supervision ..........................................................................................5-146
5.6.5.6 With double voltage supervision..........................................................................................5-149
5.6.5.7 With double voltage supervision and serial resistor in voltage monitors.........5-150
5.6.6 Analog board specific settings................................................................................... 5-152
5.6.7 Virtual inputs....................................................................................................................... 5-152
5.6.7.1 Virtual inputs writing..................................................................................................................5-152
5.6.7.2 Virtual inputs status monitoring:..........................................................................................5-152
5.6.8 Virtual outputs.................................................................................................................... 5-153
5.6.9 Virtual outputs latched................................................................................................... 5-153
5.7 Remote comms .............................................................................................5-154
5.8 Testing............................................................................................................5-155
5.8.1 Force IO–input testing .................................................................................................... 5-155
5.8.2 Force IO–output testing................................................................................................. 5-155
5.9 Relay configuration......................................................................................5-156
5.9.1 Outputs.................................................................................................................................. 5-156
5.9.2 LEDs......................................................................................................................................... 5-157
5.9.3 Operations............................................................................................................................ 5-158
5.9.3.1 Programming an operation....................................................................................................5-160
5.9.4 Protection elements......................................................................................................... 5-162
5.9.5 Control elements tab.......................................................................................................5-163
5.9.6 Oscillography...................................................................................................................... 5-164
5.9.7 Control events .................................................................................................................... 5-165
5.9.8 Switchgear ........................................................................................................................... 5-167
5.9.9 HMI (human-machine interface)................................................................................ 5-169
5.9.10 Device display selection................................................................................................ 5-174
5.9.10.1 Type of graphical display........................................................................................................5-174
5.10 Logic configuration (PLC editor).................................................................5-175
5.10.1 Theory of operation......................................................................................................... 5-176
5.10.1.1 Description......................................................................................................................................5-176
5.10.1.2 Logic compilation ........................................................................................................................5-179
5.10.2 Main menu ........................................................................................................................... 5-180
5.10.3 Configuration generation.............................................................................................. 5-181
5.10.3.1 Create new project .....................................................................................................................5-181
5.10.3.2 Create equation ...........................................................................................................................5-181
5.10.3.3 Add input to automation..........................................................................................................5-181
5.10.3.4 Add output to automation ......................................................................................................5-182
5.10.3.5 Add digital operation .................................................................................................................5-182
5.10.3.6 Link inputs, outputs, and operations..................................................................................5-182
5.10.3.7 Add library ......................................................................................................................................5-182
To Next Page
Loading...