Index
Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide 1753
marker set for voltage measurement, 1529,
1530
marker sets start time, 1521
marker time, 1520
markers for delta voltage
measurement, 1528
markers track measurements, 613
markers, command overview, 529
markers, mode, 531
markers, time at start, 1525
markers, time at stop, 1524
markers, X delta, 530, 538
markers, X1 position, 533
markers, X1Y1 source, 534
markers, X2 position, 536
markers, X2Y2 source, 537
markers, Y delta, 545
markers, Y1 position, 542
markers, Y2 position, 544
mask, 234, 248
mask command, bus, 329
mask statistics, reset, 677
mask statistics, saving, 840
mask test commands, 665
Mask Test Event Enable Register
(MTEenable), 274
mask test event event register, 276
Mask Test Event Event Register
(:MTERegister[:EVENt]), 276, 1578
mask test run mode, 684
mask test termination conditions, 684
mask test, all channels, 670
mask test, enable/disable, 682
mask, delete, 681
mask, get as binary block data, 680
mask, load from binary block data, 680
mask, lock to signal, 683
mask, recall, 816
mask, save, 833, 834
masks, bind levels, 692
master summary status bit, 251
math filters, 491
math function, stop displaying, 266
math operators, 490
math transforms, 490
math visualizations, 492
MAV (Message Available), 233, 249
, 251
max hold math function, 492
maximum duration, 1333, 1356, 1357
maximum math function, 492
maximum number of peaks for FFT peak
search, 1167
maximum position, 1284
maximum random trigger holdoff
time, 1302
maximum range for zoomed window, 1292
maximum scale for zoomed window, 1293
maximum vertical value measurement, 631
maximum vertical value, time of, 638,
1522
maximum waveform data length, 848
MEASure commands, 549
measure mask test failures, 685
measure overshoot, 600
measure period, 603
measure phase between channels, 604
MEASure power commands, 641
measure preshoot, 606
measure start voltage, 1529
measure stop voltage, 1530
measure value at a specified time, 640,
1531
measure value at top of waveform, 636
measurement error, 568
measurement record, 1408
measurement results, saving, 841
measurement setup, 568, 615
measurement source, 615
measurement statistics results, 608
measurement statistics, display on/off, 618
measurement trend math function, 492
measurement window, 637
measurements, AC RMS, 588, 635
measurements, area, 571, 583
measurements, average value, 585, 629
measurements, base value, 586, 630
measurements, built-in, 79
measurements, burst width, 573
measurements, clear, 574, 1519
measurements, command overview,
568
measurements, counter, 575
measurements, DC RMS, 588, 635
measurements, definition setup, 578
measurements, fall time, 590
measurements, falling edge count, 597
measurements, falling pulse count, 598
measurements, frequency, 595
measurements, how autoscale affects, 261
measurements, lower threshold level, 1518
measurements, maximum vertical
value, 631
measurements, maximum vertical value,
time of, 638, 1522
measurements, minimum vertical
value, 632
measurements, minimum vertical value,
time of, 639, 1523
measurements, negative duty cycle, 596
measurements, overshoot, 600
measurements, period, 603
measurements, phase, 604
measurements, positive duty cycle, 589
measurements, preshoot, 606
measurements, pulse width, negative, 599
measurements, pulse width, positive, 607
measurements, ratio of AC RMS
values, 634
measurements, rise time, 611
measurements, rising edge count, 602
measurements, rising pulse count, 605
measurements, show, 613
measurements, slew rate, 614
measurements, snapshot all, 570
measurements, source channel, 615
measurements, standard deviation, 612
measurements, start marker time, 1524
measurements, stop marker time, 1525
measurements, thresholds, 1521
measurements, time between start and stop
markers, 1520
measurements, time between trigger and
edge, 623
measurements, time between trigger and
vertical value, 626
measurements, time between trigger and
voltage level, 1526
measurements, upper threshold
value, 1527
measurements, vertical amplitude, 584,
628
measurements, vertical peak-to-peak, 587
,
633
measurements, voltage difference, 1528
memory depth, setting (Digitizer
mode), 308
memory setup, 247, 1277
menu, display, 420
menu, system, 1545
message available bit, 251
message available bit clear, 233
message decode/triggering format,
SENT, 1044
message displayed, 251
message error, 1549
message queue, 1567
message, CAN symbolic search, 1193
message, CAN symbolic trigger, 904
message, clear from display, 421
message, LIN symbolic search, 1221
message, LIN symbolic trigger, 989
messages ready, 251
midpoint of thresholds, 603
MIL-STD-1553 demo signal, 388
MIL-STD-1553 serial decode base, 994
MIL-STD-1553 serial search, data, 1226
MIL-STD-1553 serial search, mode, 1225
MIL-STD-1553 serial search, Remote
Terminal Address, 1227
MIL-STD-1553, dual demo signal, 389
min hold math function, 492
minimum duration, 1332, 1356, 1357,
1359
minimum math function, 492
minimum random trigger holdoff
time, 1303
minimum vertical value measurement, 632
minimum vertical value, time of, 639, 1523
MISO data pattern width, 1085
MISO data pattern, SPI trigger, 1084
MISO data source, SPI trigger, 1082
MISO data, SPI, 1421
mixed-signal demo signals, 387
mixed-signal oscilloscopes, 6
mnemonics, duplicate, 1615
mode, 531, 1283, 1378
mode, serial decode, 857
To Next Page
Loading...
Need help?
General
