Index
Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide 1577
trigger channel source, 1178, 1219
TRIGger commands, 1139
TRIGger commands, general, 1141
trigger data, UART, 963
TRIGger DELay commands, 1151
trigger duration, 1195, 1196
TRIGger EBURst commands, 1158
TRIGger EDGE commands, 1163
trigger edge coupling, 1165
trigger edge slope, 1168
trigger edge slope, Edge Then Edge
trigger, 1156
trigger edge source, Edge Then Edge
trigger, 1157
trigger event bit, 261
Trigger Event Register (TER), 1401
trigger event, NFC trigger, 1184
TRIGger FLEXray commands, 824
TRIGger GLITch commands, 1170
trigger holdoff, 1144
trigger idle, UART, 964
TRIGger IIC commands, 862
trigger level auto set up, 1145
trigger level constants, 311
trigger level voltage, 1166
trigger level, high, 1146
trigger level, low, 1147
TRIGger LIN commands, 872
TRIGger M1553 commands, 890
TRIGger NFC commands, 1179
trigger occurred, 219
TRIGger OR commands, 1189
TRIGger PATTern commands, 1191
trigger pattern qualifier, 1197
trigger qualifier, UART, 965
trigger reset conditions, 213, 1110
TRIGger RUNT commands, 1199
TRIGger SHOLd commands, 1204
trigger SPI clock slope, 933
TRIGger SPI commands, 930
trigger status bit, 261
trigger sweep mode, 1139
TRIGger TV commands, 1210, 1215
trigger type, ARINC 429, 776, 1026
trigger type, SPI, 944
trigger type, UART, 966
TRIGger UART commands,
946
TRIGger USB commands, 968
TRIGger ZONE commands, 1225
trigger, ARINC 429 source, 769
trigger, CAN, 794
trigger, CAN FD sample point, 787
trigger, CAN pattern data length, 800
trigger, CAN pattern ID mode, 803
trigger, CAN sample point, 789
trigger, CAN signal baudrate, 790
trigger, CAN signal definition, 791
trigger, CAN source, 793
trigger, duration greater than, 1195
trigger, duration less than, 1196
trigger, duration range, 1198
trigger, edge coupling, 1165
trigger, edge level, 1166
trigger, edge reject, 1167
trigger, edge slope, 1168
trigger, edge source, 1169
trigger, FLEXray, 834
trigger, FLEXray error, 835
trigger, FLEXray event, 838
trigger, force a, 1142
trigger, glitch greater than, 1172
trigger, glitch less than, 1173
trigger, glitch level, 1174
trigger, glitch polarity, 1175
trigger, glitch qualifier, 1176
trigger, glitch range, 1177
trigger, glitch source, 1178
trigger, high frequency reject filter, 1143
trigger, holdoff, 1144
trigger, I2S, 852
trigger, I2S alignment, 845
trigger, I2S audio channel, 854
trigger, I2S clock slope, 847
trigger, I2S CLOCksource, 849
trigger, I2S DATA source, 850
trigger, I2S pattern data, 855
trigger, I2S pattern format, 857
trigger, I2S range, 858
trigger, I2S receiver width, 848
trigger, I2S transmit word size, 860
trigger, I2S word select (WS) low, 861
trigger, I2S word select (WS) source, 851
trigger, IIC clock source, 864
trigger, IIC data source, 865
trigger, IIC pattern address, 866
trigger, IIC pattern data, 867
trigger, IIC pattern data 2, 868
trigger, IIC qualifier, 869
trigger, IIC signal baudrate, 877
trigger, IIC type, 870
trigger, LIN, 881
trigger, LIN pattern data, 883
trigger, LIN pattern data length, 885
trigger, LIN pattern format, 886
trigger, LIN sample point, 876
trigger, LIN signal definition, 1378
trigger, LIN source, 878
trigger, mode, 1148
trigger, noise reject filter, 1149
trigger, Nth edge burst source, 1162
trigger, Nth edge in burst slope, 1161
trigger, Nth edge of burst count, 1159
trigger, Nth edge of Edge Then Edge
trigger, 1155
trigger, SPI clock slope, 933
trigger, SPI clock source, 936
trigger, SPI clock timeout, 934
trigger, SPI frame source, 937
trigger, SPI framing, 935
trigger, SPI pattern MISO width, 941
trigger, SPI pattern MOSI width, 943
trigger, sweep, 1150
trigger, threshold, 1382
trigger, TV line, 1216
trigger, TV mode, 1217, 1383
trigger, TV polarity, 1218
trigger, TV source, 1219
trigger, TV standard, 1220
trigger, UART base, 961
trigger, UART baudrate, 950
trigger, UART bit order, 951
trigger, UART parity, 957
trigger, UART polarity, 958
trigger, UART Rx source, 959
trigger, UART Tx source, 960
trigger, UART width, 967
trigger, USB, 976
truncation rules, 1430
TST (Self Test), 221
tstart, 1360
tstop, 1361
TTL threshold voltage for digital
channels, 357, 1336
TTL trigger threshold voltage, 1382
turn function on or off, 1348
turn off channel, 234
turn off channel labels, 371
turn off digital pod, 234
turn off math function, 234
turn off time, 567, 664, 665
turn on channel labels, 371
turn on channel number display, 1341
turn on time, 568, 664, 665
turn on/turn off analysis thresholds, 665
turn on/turn off time analysis, 661, 662,
663, 664
turning channel display on and off, 306
turning off/on function calculation, 401
turning vectors on or off, 1340
TV mode, 1217, 1383
TV trigger commands, 1210, 1215
TV trigger line number setting, 1216
TV trigger mode, 1219
TV trigger polarity, 1218
TV trigger standard setting, 1220
TV triggering, 1140
tvmode, 1383
Tx data, UART, 1259
Tx frame count (UART), 955
Tx source, 960
type of power being converted, efficiency
measurement, 640
type, USB 2.0 signal quality test, 335
U
UART base, 961
UART baud rate, 950
UART bit order, 951
UART frame counters, reset, 953
UART parity, 957
UART polarity, 958
UART Rx source, 959
UART SEARch commands, 1081
UART serial search, data, 1082
To Next Page
Loading...
