1576 Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
Index
start cursor, 1360
start frequency, FFT math function, 403
start measurement, 488
start print job, 445
start time, 1177, 1360
start time marker, 1357
starting bit for SENT Fast Channel
Signal, 916
starting byte of data, CXPI trigger, 819
state memory, 215
state of instrument, 207, 1120
statistics increment, 533
statistics reset, 535
statistics results, 523
statistics, max count, 534
statistics, relative standard deviation, 536
statistics, type of, 531
status, 218, 259, 261
Status Byte Register (STB), 216, 218, 219,
1398
status data structure clear, 201
status registers, 80
status reporting, 1393
STB (Status Byte Register), 216, 218, 219,
1398
steady state output voltage expected, 695,
696, 697
step size for frequency span, 407
stop, 235, 260
stop acquisition, 260
stop cursor, 1361
stop displaying channel, 234
stop displaying math function, 234
stop displaying pod, 234
stop frequency, FFT math function, 404
stop on mask test failure, 602
stop time, 1177, 1361
storage, 215
store instrument setup, 207, 215
store setup, 215
storing calibration information, 292
string variables, 78
string variables, reading multiple query
results into, 79
string variables, reading query results into
multiple, 79
string, quoted ASCII, 194
subnet mask, 64
subsource, waveform source, 1259
subsystem commands, 3, 1433
subtract math function, 416, 1255
subtract math function as g(t) source, 1344
sweep mode, trigger, 1139, 1150
sweep speed set to fast to measure fall
time, 509
sweep speed set to fast to measure rise
time, 526
switch disable, 1108
switching level, current, 704
switching level, voltage, 707
switching loss per cycle, 561
switching loss power analysis, 702
sync break, LIN, 880
sync frame count (FlexRay), 831
syntax elements, 193
syntax rules, program data, 1432
syntax, optional terms, 193
syntax, program message, 1429
SYSTem commands, 1103
system commands, 1105, 1106, 1107,
1108, 1120, 1122
system commands introduction, 1104
T
table of current harmonics results, 644
tdelta, 1356
tedge, 537
Tektronix probe model number, 314
telnet ports 5024 and 5025, 1243
Telnet sockets, 81
temporary message, 1106
TER (Trigger Event Register), 261, 1401
termination conditions, mask test, 598
test sigma, mask test run, 603
test, self, 221
test, USB 2.0 signal quality, 333
text, writing to display, 1106
THD (total harmonics distortion), 653
threshold, 357, 617, 1336, 1382
threshold for FFT peak search, 1013
threshold voltage (lower) for
measurement, 1354
threshold voltage (upper) for
measurement, 1363
thresholds, 498, 1357
thresholds used to measure period, 518
thresholds, how autoscale affects, 229
time base, 1127, 1128, 1129, 1133,
1381
time base commands introduction, 1126
time base reference, 1131
time base reset conditions, 213, 1110
time base window, 1135, 1136, 1137
time between arm and trigger, NFC arm and
trigger event, 1181
time between points, 1356
time buckets, 265, 266
time delay, 1381
time delay, Edge Then Edge trigger, 1154
time delta, 1356
time difference between data points, 1263
time duration, 1177, 1195,
1196, 1198
time holdoff for trigger, 1144
time interval, 537, 539, 1356
time interval between trigger and
occurrence, 1362
time marker sets start time, 1357
time measurements with X cursors, 463
time per division, 1129
time record, 409
time reference, lister, 450
time specified, 549
time, calibration, 299
time, mask test run, 604
time, runt pulse search, 1018
time, runt trigger, 1203
time, start marker, 1360
time, stop marker, 1361
time, system, 1122
time, transition search, 1023
time, transition trigger, 1214
time/div, how autoscale affects, 229
time-at-max measurement, 1358
time-at-min measurement, 1359
TIMebase commands, 1125
timebase vernier, 1134
TIMebase:MODE, 76
time-ordered label list, 372
timeout enable, NFC arm and trigger
event, 1187
timeout occurred, NFC arm and trigger
event, 1186
timeout period, NFC arm and trigger
event, 1188
timeout, SPI clock, 934
timing measurement, 488
title channels, 309
title, mask test, 612
token PID, USB search, 1099
token PID, USB trigger, 989
tolerance for determining valid SENT sync
pulses, 920
tolerance, automask, 588, 589
top of waveform value measured, 550
total frame count (CAN), 784
total frame count (FlexRay), 832
total harmonics distortion (THD), 653
total waveforms in mask test, 593
touchscreen on/off, 1123
trace memory, 259
track measurements, 528
tracking, dual channel waveform
generator, 1308
transfer instrument state, 207, 1120
transforms, math, 416
transient response, 576
transient response analysis, 708, 709, 712
TRANsition SEARch commands, 1019
transition search qualifier, 1020
transition search slope, 1021
transition search time, 1023
transition trigger qualifier, 1211
transition trigger slope, 1212
transition trigger source, 1022, 1213
transition trigger time, 1214
transmit word size, I2S, 860
transparent screen background, remote
command logging, 1118
tree traversal rules, 1433
trend measurement, 427
TRG (Trigger), 217, 219, 220
TRIG OUT BNC, 293
trigger armed event register, 247, 249
trigger burst, UART, 962
To Next Page
Loading...
