1754 Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
Index
model number, 238
models, oscilloscope, 3
modes for triggering, 1308
Modify softkey, 72
modulating signal frequency, waveform
generator, 1454, 1456
modulation (waveform generator),
enabling/disabling, 1462
modulation analysis, 751
modulation analysis source (voltage or
current), 752
modulation analysis, type of, 753
modulation type, waveform
generator, 1463
MOSI data pattern width, 1087
MOSI data pattern, SPI trigger, 1086
MOSI data source, SPI trigger, 1083, 1544
most significant byte first, 1401
move cursors, 1524, 1525
msbfirst, 1401
MSG (Message), 249, 251
MSO models, 6
MSS (Master Summary Status), 251
MTEenable (Mask Test Event Enable
Register), 274
MTERegister[:EVENt] (Mask Test Event Event
Register), 276, 1578
MTESt commands, 665
multi-channel waveform data, save, 835
multiple commands, 1615
multiple queries, 87
multiplier value for SENT Fast Channel
Signal, 1053
multiply math function, 490, 1417
multiply math function as g(t) source, 1508
N
N2820A high sensitivity current probe, 60,
583, 584, 585, 586, 587, 588
N8900A Infiniium Offline oscilloscope
analysis software, 835
name channels, 352
name list, 419
natural logarithm math function, 491
negative glitch trigger polarity, 1335
negative pulse width, 599
negative pulse width measurement, 79
negative pulse width, power modulation
analysis, 753
negative slope, 1076, 1328
negative slope, Nth edge in burst, 1321
negative TV trigger polarity, 1379
network domain password, 515
network domain user name, 517
network printer address, 512
network printer domain, 514
network printer slot, 516
network printer, apply connection
settings, 513
new line (NL) terminator, 223, 1612
new load current, transient response
analysis, 806
NFC demo signal, 387
NFC trigger commands, 1339
nibble order for SENT Fast Channel
Signal, 1057
NL (new line) terminator, 223, 1612
NM bits (CXPI), triggering on, 923
NMONotonic, dual demo signal, 389
noise floor, 799, 802
noise reject filter, 1309
noise waveform generator output, 1447
noise, adding to waveform generator
output, 1461
noisy sine waveform demo signal, 386
non-core commands, 1610
non-interlaced GENeric mode, 1381
non-volatile memory, label list, 328, 396,
419
normal acquisition type,
300, 1397
normal trigger sweep mode, 1295
notices, 2
NR1 number format, 223
NR3 number format, 223
NRZ baud rate, 1021
NRZ bit order, 1022
NRZ bit values trigger, data value, 1033
NRZ bit values trigger, data width, 1034
NRZ bus display format, 1023
NRZ decode base, 1020
NRZ frame size, 1025
NRZ idle state level, 1028
NRZ idle time in bits, 1027
NRZ number of bits in header field, 1026
NRZ number of bits in trailer field, 1035
NRZ number of bits per word in data
field, 1036
NRZ number of start bits, 1031
NRZ number of words in data field, 1024
NRZ polarity, 1029
NRZ serial bus commands, 1018
NRZ signal source, 1030
NRZ trigger mode, 1032
Nth edge burst trigger source, 1322
Nth edge burst triggering, 1296
Nth edge in a burst idle, 1320
Nth edge in burst slope, 1321
Nth edge of burst counter, 1319
Nth edge of Edge Then Edge trigger, 1315
NTSC, 1377, 1381
null frame count (FlexRay), 929
null offset, 799
NULL string, 1263
number format, 223
number of nibbles, SENT message, 1047
number of points, 308, 1406, 1408
number of time buckets, 1406, 1408
numeric variables, 86
numeric variables, reading query results into
multiple, 88
nwidth, 599
O
obsolete and discontinued
commands, 1491
obsolete commands, 1610
Occupied Bandwidth, FFT analysis
measurement, 593
occurrence reported by magnitude, 1526
offset, 460
offset for Ax + B math operation, 488
offset value for channel voltage, 353
offset value for selected function, 489, 495
offset value for SENT Fast Channel
Signal, 1055
offset, waveform generator, 1480
one values in waveform data, 1403
OPC (Operation Complete) command, 240
OPC (Operation Complete) status bit, 234,
236
OPEE (Operation Status Enable
Register), 278
Open method, 81
operating configuration, 239, 1277
operating state, 247
operation complete, 240
operation status condition register, 280
Operation Status Condition Register
(:OPERegister:CONDition), 280, 1573
operation status conditions occurred, 251
Operation Status Enable Register
(OPEE), 278
operation status event register, 283
Operation Status Event Register
(:OPERegister[:EVENt]), 283, 1571
operations for function, 490
operators, math, 490
OPERegister:CONDition (Operation Status
Condition Register), 280, 1573
OPERegister[:EVENt] (Operation Status
Event Register), 283, 1571
OPT (Option Identification), 241
optional syntax terms, 223
options, 241
OR trigger commands, 1350
order of digital channels on display, 1505
order of output, 1401
oscilloscope connection, opening, 81
oscilloscope connection, verifying, 73
oscilloscope external trigger, 433
oscilloscope models, 3
oscilloscope, connecting, 71
oscilloscope, initialization, 78
oscilloscope, operation, 6
oscilloscope, program structure, 78
oscilloscope, setting up, 71
oscilloscope, setup, 82
output control, demo signals, 392
output control, waveform generator, 1465
output load impedance, waveform
generator, 452, 1466
output messages ready, 251
output polarity, waveform generator, 1468
To Next Page
Loading...
Need help?
General
