Index
Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide 1569
I
I1080L50HZ, 1216, 1220
I1080L60HZ, 1216, 1220
I2C demo signal, 345
I2S alignment, 845
I2S audio channel, 854
I2S clock slope, 847
I2S CLOCk source, 849
I2S DATA source, 850
I2S demo signal, 346
I2S pattern data, 855
I2S pattern format, 857
I2S range, 858
I2S receiver width, 848
I2S SEARch commands, 1046
I2S serial bus commands, 843
I2S serial decode base, 846
I2S serial search, audio channel, 1047
I2S serial search, data, 1049
I2S serial search, format, 1050
I2S serial search, mode, 1048
I2S serial search, range, 1051
I2S transmit word size, 860
I2S trigger operator, 852
I2S triggering, 756
I2S word select (WS) low, 861
I2S word select (WS) source, 851
ID filter for CAN trigger, 797
id mode, 803
ID pattern, CAN trigger, 802
identification number, 206
identification of options, 209
identifier, LIN, 882
idle, 1160
idle state, SENT bus, 906
idle until operation complete, 208
IDN (Identification Number), 206
IEC 61000-3-2 standard for current
harmonics analysis, 651
IEEE 488.2 standard, 200
IIC address, 866
IIC clock, 864
IIC data, 865, 867
IIC data 2, 868
IIC SEARch commands, 1052
IIC serial decode address field size, 863
IIC serial search, address, 1055
IIC serial search, data, 1056
IIC serial search, data2, 1057
IIC serial search, mode, 1053
IIC serial search, qualifier, 1058
IIC trigger commands, 862
IIC trigger qualifier, 869
IIC trigger type, 870
IIC triggering, 756
image format, 732
image invert graticule colors, 733
image memory, 259
image palette, 734
image, save, 730
image, save with inksaver, 733
impedance, 307
infinity representation, 1435
initial load current, transient response
analysis, 710
initialization, 70, 73
initialize, 212, 1109
initialize label list, 372
initiate acquisition, 235
inksaver, save image with, 733
input coupling for channels, 305
input for integrate, DC offset
correction, 412
input impedance for channels, 307, 1338
input inversion for specified channel, 308
input power, 566
input source, Control Loop Response (Bode)
power analysis, 633
input source, Power Supply Rejection Ratio
(PSRR) power analysis, 674
inrush current, 570
inrush current analysis, 654, 655, 656
inrush current expected, 690
insert label, 309
installed options identified, 209
instruction header, 1429
instrument number, 206
instrument options identified, 209
instrument requests service, 219
instrument serial number, 257
instrument settings, 430
instrument status, 80
instrument type, 206
integrate DC offset correction, 412
integrate math function, 416, 1255
INTegrate source for function, 1347
intensity, waveform, 370
internal low-pass filter, 304, 384
introduction to :ACQuire commands, 264
introduction to :BUS<n> commands, 280
introduction to :CALibrate commands, 290
introduction to :CHANnel<n>
commands, 303
introduction to :COUNter commands, 337
introduction to :DEMO commands, 343
introduction to :DIGital<d>
commands, 352
introduction to :DISPlay commands, 360
introduction to :EXTernal commands, 383
introduction to :FUNCtion commands, 393
introduction to :HARDcopy
commands, 430
introduction to :LISTer commands, 447
introduction to :MARKer commands, 453
introduction to :MEASure commands, 488
introduction to :POD<n> commands, 613
introduction to :RECall commands, 714
introduction to :SAVE commands, 725
introduction to :SBUS commands, 755
introduction to :SYSTem commands, 1104
introduction to :TIMebase
commands, 1126
introduction to :TRIGger commands, 1139
introduction to :WAVeform
commands, 1235
introduction to :WGEN<w>
commands, 1272
introduction to :WMEMory<r>
commands, 1317
introduction to common (*)
commands, 200
introduction to root (:) commands, 226
invert graticule colors for hardcopy, 435,
1352
invert graticule colors for image, 733
inverted masks, bind levels, 606
inverting input for channels, 308
IO library, referencing, 72
IP address, 64
IronPython, SCPI.NET example, 1556
K
key disable, 1108
key press detected in Standard Event Status
Register, 205
KEYSight demo signal, 347
Keysight Interactive IO application, 67
Keysight IO Control icon, 65
Keysight IO Libraries Suite, 6, 61, 72, 74
Keysight IO Libraries Suite, installing, 62
knob disable, 1108
known state, 212, 1109
L
label, 1335
label command, bus, 286
label list, 309, 372
label reference waveforms, 1321
label, ARINC 429 trigger, 771, 775, 1025
label, digital channel, 354
labels, 309, 371, 372
labels to store calibration information, 292
labels, specifying, 360
LAN instrument, 66
LAN interface, 63, 64, 65
LAN Settings softkey, 64
landscape layout for hardcopy, 436
language for program examples, 69
layout for hardcopy, 436
leakage into peak spectrum, 409
learn string, 207, 1120
least significant byte first, 1241
left time base reference, 1131
legal values for channel offset, 310
legal values for frequency span, 407
legal values for offset, 415, 421
length for waveform data, 749
length of data, CXPI trigger, 818
less than qualifier, 1176
less than time, 1173, 1177, 1196, 1198
less than value for glitch search, 1004
To Next Page
Loading...
