Index
Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide 1567
Duty Cycle, power modulation
analysis, 660
DVM commands, 377
DVM displayed value, 379
DVM enable/disable, 380
DVM input source, 382
DVM mode, 381
E
EBURst trigger commands, 1158
ECL channel threshold, 1336
ECL threshold voltage for digital
channels, 357
ECL trigger threshold voltage, 1382
edge activity, 1334
edge counter, Edge Then Edge
trigger, 1155
edge counter, Nth edge of burst, 1159
edge coupling, 1165
edge fall time, 509
edge parameter for delay
measurement, 500
edge preshoot measured, 521
edge rise time, 526
EDGE SEARch commands, 999
edge search slope, 1000
edge search source, 1001
edge slope, 1168
edge source, 1169
edge string for OR'ed edge trigger, 1190
EDGE trigger commands, 1163
edge triggering, 1140
edges (activity) on digital channels, 227
edges in measurement, 498
efficiency, 563
efficiency power analysis, apply, 639
elapsed time in mask test, 592
ellipsis, 194
enable channel labels, 371
enabling calibration, 295
enabling channel display, 306
enabling status register bits, 202, 216
end of string (EOS) terminator, 1430
end of text (EOT) terminator, 1430
end or identify (EOI), 1430
endpoint value, USB search, 1092
endpoint value, USB trigger, 981
energy loss, 564
envelope math function, 417
EOI (end or identify), 1430
EOS (end of string) terminator, 1430
EOT (end of text) terminator, 1430
equivalent time acquisition mode, 267
erase data, 368
erase measurements, 1355
erase screen, 1342
error counter (ARINC 429), 764
error counter (ARINC 429), reset, 765
error frame count (CAN), 780
error frame count (UART), 952
error messages, 1107, 1385
error number, 1107
error queue, 1107, 1406
error, measurement, 488
ESB (Event Status Bit), 217, 219
ESE (Standard Event Status Enable
Register), 202, 1405
ESR (Standard Event Status Register), 204,
1404
ET value, USB search, 1093
ET value, USB trigger, 982
ETE demo signal, 345
event status conditions occurred, 219
Event Status Enable Register (ESE), 202,
1405
Event Status Register (ESR), 204, 261,
1404
example code, :ACQuire:COMPlete, 265
example code, :ACQuire:SEGMented, 272
example code, :ACQuire:TYPE, 277
example code, :AUToscale, 230
example code, :CHANnel<n>:LABel, 309
example code, :CHANnel<n>:PROBe, 311
example code, :CHANnel<n>:RANGe, 320
example code, :DIGitize, 236
example code, :DISPlay:DATA, 369
example code, :DISPlay:LABel, 371
example code, :DISPlay:ORDer, 1341
example code, :MEASure:PERiod, 530
example code, :MEASure:RESults, 523
example code, :MEASure:TEDGe, 538
example code, :MTESt, 581
example code, :POD<n>:THReshold, 617
example code, :RUN/:STOP, 256
example code, :SYSTem:SETup, 1120
example code, :TIMebase:DELay, 1381
example code, :TIMebase:MODE, 1127
example code, :TIMebase:RANGe, 1129
example code, :TIMebase:REFerence, 1131
example code, :TRIGger:MODE, 1148
example code, :TRIGger:SLOPe, 1168
example code, :TRIGger:SOURce, 1169
example code, :VIEW and :BLANk, 262
example code, :WAVeform, 1256
example code, :WAVeform:DATA, 1243
example code, :WAVeform:POINts, 1247
example code,
:WAVeform:PREamble, 1251
example code,
:WAVeform:SEGMented, 272
example code, *RST, 214
example programs, 6, 1437
excursion delta for FFT peak search, 1010
EXE (Execution Error) status bit, 203, 205
execution error detected in Standard Event
Status, 205
exponential fall waveform generator
output, 1284
exponential math function, 417
exponential notation, 193
exponential rise waveform generator
output, 1284
extended video triggering license, 1220
external glitch trigger source, 1178
external range, 386
external trigger, 383, 385, 1169
EXTernal trigger commands, 383
EXTernal trigger level, 1166
external trigger probe attenuation
factor, 385
external trigger probe sensing, 1343
EXTernal trigger source, 1169
external trigger units, 387
F
fail count, current harmonics analysis, 645
fail/pass status (overall) for current
harmonics analysis, 652
failed waveforms in mask test, 590
failure, self test, 221
fall time measurement, 488, 509
Fall Time, power modulation analysis, 660
falling edge count measurement, 512
falling pulse count measurement, 513
FAST data, SENT, 1259
Fast Fourier Transform (FFT)
functions, 402, 407, 409, 416, 1347
FF values in waveform data, 1243
FFT (Fast Fourier Transform) functions, 402,
407, 409, 416, 1347
FFT (Fast Fourier Transform)
operation, 1255
FFT vertical units, 408
FFTPhase (Fast Fourier Transform)
functions, 416
fifty ohm impedance, disable setting, 1112
filename for hardcopy, 1350
filename for recall, 717, 1281
filename for save, 729
filter CXPI trigger by ID, 815
filter for frequency reject, 1167
filter for high frequency reject, 1143
filter for noise reject, 1149
filter used to limit bandwidth, 304, 384
filters to Fast Fourier Transforms, 409
filters, math, 417
fine horizontal adjustment (vernier), 1134
fine vertical adjustment (vernier), 323
finish pending device operations, 208
first point displayed, 1265
FLATtop window for amplitude
measurements, 409
FLEXray autoset for event trigger, 836
FLEXray autosetup, 826
FlexRay demo signal, 346
FlexRay frame counters, reset, 830
FLEXray SEARch commands, 1040
FlexRay serial search, cycle,
1041
FlexRay serial search, data, 1042
FlexRay serial search, data length, 1043
FlexRay serial search, frame, 1044
FlexRay serial search, mode, 1045
To Next Page
Loading...
