1564 Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
Index
auto setup for M1553 trigger, 891
auto setup for power analysis signals, 681
auto trigger sweep mode, 1139
automask create, 585
automask source, 586
automask units, 587
automatic measurements constants, 311
automatic probe type detection, 1339,
1343
autoscale, 229
autoscale acquire mode, 231
autoscale channels, 232
AUToscale command, 74
autoset for FLEXray event trigger, 836
autosetup for FLEXray decode, 826
average math function, clear, 400
average value measurement, 504, 542
Average, power modulation analysis, 660
averaged value math function, 417
averaging acquisition type, 264, 1237
averaging, synchronizing with, 1424
Ax + B math function, 416
B
bandwidth filter limits, 384
bandwidth filter limits to 20 MHz, 304
bar chart of current harmonics results, 644
base 10 exponential math function, 417
base value measurement, 505, 543
base, ARINC 429, 763
base, I2S serial decode, 846
base, MIL-STD-1553 serial decode, 892
base, SENT decode, 902
base, UART trigger, 961
base, USB decode, 971
basic instrument functions, 200
baud rate, 790, 877, 950
baud rate, CAN FD, 792
begin acquisition, 235, 256, 258
BHARris window for minimal spectral
leakage, 409
binary block data, 194, 369, 1120, 1243
BINary waveform data format, 748
bind levels for masks, 606
bit order, 951
bit order, SPI decode, 932
bit rate measurement, 492
bit selection command, bus, 281
bit weights, 204
bitmap display, 369
bits in Service Request Enable
Register, 217
bits in Standard Event Status Enable
Register, 203
bits in Status Byte Register, 219
bits selection command, bus, 282
blank, 234
block data, 194, 207, 1120
block response data, 78
blocking synchronization, 1419
blocking wait, 1418
BMP format screen image data, 369
braces, 193
built-in measurements, 71
burst data demo signal, 345
burst width measurement,
493
burst, minimum time before next, 1160
bus bit selection command, 281
bus bits selection commands, 282
bus clear command, 284
bus commands, 280
BUS data format, 1240
bus display, 285
bus label command, 286
bus mask command, 287
BUS<n> commands, 279
button disable, 1108
button, calibration protect, 295
byte format for data transfer, 1239, 1245
BYTeorder, 1241
C
C, SICL library example, 1524
C, VISA library example, 1471
C#, SCPI.NET example, 1544
C#, VISA COM example, 1447
C#, VISA example, 1490
CAL PROTECT button, 295
CAL PROTECT switch, 290
calculating preshoot of waveform, 521
calculating the waveform overshoot, 515
calibrate, 291, 292, 295, 299
CALibrate commands, 289
calibrate date, 291
calibrate introduction, 290
calibrate label, 292
calibrate output, 293
calibrate start, 296
calibrate status, 297
calibrate switch, 295
calibrate temperature, 298
calibrate time, 299
CAN acknowledge, 789
CAN and LIN demo signal, 346
CAN baud rate, 790
CAN demo signal, 345
CAN FD baud rate, 792
CAN FD data triggers, starting byte
position, 801
CAN frame counters, reset, 782
CAN SEARch commands, 1030
CAN serial bus commands, 777
CAN serial search, data, 1033
CAN serial search, data length, 1034
CAN serial search, ID, 1035
CAN serial search, ID mode, 1036
CAN serial search, mode, 1031
CAN signal definition, 791
CAN source, 793
CAN symbolic data display, 786
CAN symbolic data, recall, 716
CAN trigger, 794, 800
CAN trigger data pattern, 798
CAN trigger ID pattern, 802
CAN trigger pattern id mode, 803
CAN trigger, ID filter for, 797
CAN triggering, 755
capture data, 235
capturing data, 70
cardiac waveform generator output, 1284
center frequency set, 402, 416
center of screen, 1268
center screen, vertical value at, 415, 421
center time base reference, 1131
CFD demo signal, 347
channel, 262, 309, 1334, 1336
channel coupling, 305
channel display, 306
channel input impedance, 307
channel inversion, 308
channel label, 309, 1335
channel labels, 371, 372
channel numbers, 1341
channel overload, 319
channel protection, 319
channel reset conditions, 212, 1109
channel selected to produce trigger, 1178,
1219
channel signal type, 317
channel skew for oscilloscope probe, 316,
1337
channel status, 259, 1341
channel threshold, 1336
channel vernier, 323
channel, stop displaying, 234
CHANnel<n> commands, 301, 303
channels to autoscale, 232
channels, how autoscale affects, 229
characters to display, 1106
chart logic bus state math function, 418
chart logic bus state, clock edge, 396
chart logic bus state, clock source, 395
chart logic bus timing math function, 418
chart logic bus, units, 399
chart logic bus, value for data = 0, 398
chart logic bus, value for data
increment, 397
classes of input signals, 409
classifications, command, 1428
clear, 368
clear bus command, 284
clear cumulative edge variables, 1334
clear markers, 494, 1355
clear measurement, 494, 1355
clear message queue, 201
Clear method, 73
clear reference waveforms, 1319
clear screen, 1342
clear status, 201
clear waveform area, 360
clipped high waveform data value, 1243
clipped low waveform data value, 1243
To Next Page
Loading...
