1574 Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
Index
reject high frequency, 1143
reject noise, 1149
relative standard deviation, 536
remote command logging,
enable/disable, 1113, 1117
remote control examples, 1437
Remote Terminal Address (RTA), M1553
trigger, 895
remove cursor information, 455
remove labels, 371
remove message from display, 1106
reorder channels, 229
repetitive acquisitions, 256
report errors, 1107
report transition, 537, 539
reporting status, 1393
reporting the setup, 1140
request service, 219
Request-for-OPC flag clear, 201
reset, 212
reset conditions, 212
reset defauts, waveform generator, 1307
reset mask statistics, 591
reset measurements, 368
resolution of printed copy, 1351
resource session object, 73
ResourceManager object, 73
restore configurations, 207, 211, 215,
1120
restore labels, 371
restore setup, 211
return values, query, 1435
returning acquisition type, 276
returning number of data points, 268
RF burst demo signal, 345
right time base reference, 1131
ringing pulse demo signal, 344
ripple (output) analysis, 680
ripple, output, 575
rise time measurement, 488
rise time of positive edge, 526
Rise Time, power modulation analysis, 660
rising edge count measurement, 517
rising pulse count measurement, 520
RMS - AC, power modulation analysis, 660
RMS value measurement, 507, 548
roll time base mode, 1127
root (:) commands, 223, 226
root level commands, 3
RQL (Request Control) status bit, 203, 205
RQS (Request Service), 219
RS-232/UART triggering, 756
R-sense resistor value, N2825A
user-defined R-sense head, 315
RST (Reset), 212
rules, tree traversal, 1433
rules, truncation, 1430
run, 220, 256
Run bit, 247, 249
run count, current harmonics analysis, 650
run mode, mask test, 598
run, USB 2.0 signal quality test, 328
running configuration, 215, 1120
RUNT SEARch commands, 1014
runt search polarity, 1015
runt search qualifier, 1016
runt search source, 1017
runt search, pulse time, 1018
RUNT trigger commands, 1199
runt trigger polarity, 1200
runt trigger qualifier, 1201
runt trigger source, 1202
runt trigger time, 1203
Rx frame count (UART), 954
Rx source, 959
S
S and E or U value, USB search, 1102
S and E or U value, USB trigger, 992
sample rate, 3, 275
sampled data, 1340
sampled data points, 1243
SAV (Save), 215
save, 215, 725
save arbitrary waveform, 727
SAVE commands, 723
save current harmonics analysis
results, 738
save filename, 729
save image, 730
save image with inksaver, 733
save mask, 735, 736
save mask test failures, 601
save path information, 739
save reference waveform, 753
save setup, 746
save to reference waveform location, 1322
save waveform data, 747
saved image, area, 1377
saving and recalling data, 360
SBUS A429 commands, 760
SBUS CAN commands, 777
SBUS commands, 755
SBUS CXPI commands, 807
SBUS I2S commands, 843
SBUS SENT commands, 897
SBUS<n> commands, general, 757
SC value, USB search, 1101
SC value, USB trigger, 991
scale, 422, 1133, 1137
scale factors output on hardcopy, 433, 731
scale for channels, 321
scale units for channels, 322
scale units for external trigger, 387
scaling display factors, 311
SCPI commands, 81
SCPI.NET example in C#, 1544
SCPI.NET example in IronPython, 1556
SCPI.NET example in Visual Basic
.NET, 1550
SCPI.NET examples, 1544
scratch measurements, 1355
screen area for hardcopy print,
431
screen area for saved image, 1377
screen display of logged remote commands,
enable/disable, 1115
screen image data, 369
SDI pattern, ARINC 429 trigger, 773, 1028
SEARch commands, 993
SEARch commands, A429, 1024
SEARch commands, CAN, 1030
SEARch commands, EDGE, 999
SEARch commands, FLEXray, 1040
SEARch commands, general, 994
SEARch commands, GLITch, 1002
SEARch commands, I2S, 1046
SEARch commands, IIC, 1052
SEARch commands, LIN, 1059
SEARch commands, M1553, 1068
SEARch commands, PEAK, 1009
SEARch commands, RUNT, 1014
SEARch commands, SENT, 1072
SEARch commands, SPI, 1077
SEARch commands, TRANsition, 1019
SEARch commands, UART, 1081
SEARch commands, USB, 1085
search event (found) times, saving, 744
search for found event, 996
search mode, 997
search state, 998
search, edge slope, 1000
search, edge source, 1001
search, USB, 1087
SECAM, 1216, 1220
seconds per division, 1133
segmented memory acquisition times, 745
segmented waveform save option, 751
segments, analyze, 270
segments, count of waveform, 1253
segments, setting number of memory, 271
segments, setting the index, 272
segments, time tag, 1254
select measurement channel, 529
self-test, 221
sensing a channel probe, 1339
sensing a external trigger probe, 1343
sensitivity of oscilloscope input, 311
SENT demo signal, 347
SENT enhanced serial message ID and data
lengths, 928
SENT fast channel data search value, 1073
SENT fast channel data trigger setting,
923
SENT FAST data, 1259
SENT input source, 918
SENT percent tolerance variation
trigger, 929
SENT SEARch commands, 1072
SENT search mode, 1074
SENT serial bus commands, 897
SENT signal length setting, 910
SENT signals display setting, 909
SENT slow channel data search
value, 1075
To Next Page
Loading...
