Figures
1. Front view of 2073-700 file module ..... 1
2. Front view of 2073-720 file module ..... 2
3. 2073-720 file module advanced operator panel 2
4. Rear view of 2073-700 file module ..... 3
5. Rear view of 2073-720 file module ..... 3
6. Storwize V7000 Gen1 Drives on a 12-drive
enclosure.............. 4
7. Storwize V7000 Gen1 Drives on a 24-drive
enclosure.............. 5
8. Storwize V7000 Gen2 Large form factor
horizontal drive ........... 5
9. Storwize V7000 Gen2 Small form factor vertical
drive ............... 5
10. LED indicators on a single 3.5 inch drive 6
11. LED indicators on a single 2.5 inch drive 6
12. Storwize V7000 Gen1 12 drives and two end
caps ............... 7
13. Storwize V7000 Gen1 Left enclosure end cap 8
14. Rear view of a model 2076-112 or a model
2076-124 control enclosure ........ 9
15. Rear view of a model 2076-312 or a model
2076-324 control enclosure ........ 9
16. Rear view of a model 2076-212 or a model
2076-224 expansion enclosure ....... 9
17. Rear view of a Storwize V7000 Unified control
enclosure ............. 10
18. LEDs on the power supply units of the control
enclosure ............. 11
19. Rear view of a Storwize V7000 Gen2 expansion
enclosure ............. 13
20. LEDs on the power supply units of the
expansion enclosure.......... 14
21. Storwize V7000 2076-524 node canister ports 15
22. Storwize V7000 2076-524 node canister
indicators ............. 15
23. USB ports on the Storwize V7000 Gen2 node
canister .............. 21
24. Fibre Channel ports and indicators..... 22
25. Example of installed 10 Gbps Fibre Channel
over Ethernet/iSCSI host interface adapters .. 23
26. 10 Gbps Fibre Channel over Ethernet/iSCSI
host interface adapter ports ....... 23
27. 10 Gbps Fibre Channel over Ethernet/iSCSI
host interface adapter indicator LEDs .... 24
28. Fibre Channel ports on the node canisters 25
29. LEDs on the Fibre Channel ports ..... 25
30. USB ports on the node canisters...... 27
31. Ethernet ports on the 2076-112 and 2076-124
node canisters............ 28
32. 10 Gbps Ethernet ports on the 2076-312 and
2076-324 node canisters ........ 28
33. SAS ports on the node canisters. ..... 29
34. LEDs on the node canisters ....... 30
35. SAS ports and LEDs at rear of expansion
canister .............. 32
36. SAS ports and LEDs in rear of expansion
enclosure ............. 33
37. Expansion canister LEDs ........ 34
38. LEDs on the expansion canisters ..... 35
39. File module Ethernet connections. ..... 64
40. File module Ethernet connections. ..... 66
41. Connecting the file modules to the Storwize
V7000 Gen1 control enclosure using Fibre
Channel cables ........... 73
42. Connecting the file modules to a Storwize
V7000 Gen2 control enclosure that has a Fibre
Channel interface adapter in PCI slot 2 of each
node canister ............ 74
43. Locations of the power-supply LEDs .... 86
44. Selecting a file module to display node status 99
45. Displaying node status ........ 100
46. Example that shows that mirroring is
re-synchronizing .......... 102
47. Example that shows that a drive is not
synchronized............ 103
48. Example that shows that the mirror is not
created.............. 104
49. Example of a SMART error ....... 105
50. Removing the cover ......... 123
51. Installing the cover ......... 124
52. Removing the bezel ......... 126
53. Installing the bezel.......... 127
54. Configuration cable ......... 130
55. Power cable connection ........ 130
56. Hard disk drive cable connection ..... 131
57. Removing the battery ......... 133
58. Installing the battery ......... 136
59. Removing the air baffle ........ 137
60. Installing the air baffle ........ 138
61. Removing the fan bracket ....... 140
62. Installing the fan bracket........ 141
63. Installing a PCI riser-card assembly .... 143
64. Removing a PCI adapter from a PCI
riser-card assembly ......... 144
65. Inserting the adapter into the PCI connector 145
66. Removing a hot-swap hard disk drive 149
67. Installing a hot-swap hard disk drive 150
68. Locations of the DIMM connectors on the
system board ........... 154
69. Removing a hot-swap ac power supply 159
70. Removing the hot-swap drive backplane 165
71. Installing the hot-swap drive backplane 166
72. Management GUI showing CTDB status for
both file modules .......... 188
73. LEDs on the power supply units of the
control enclosure .......... 263
74. LEDs on the node canisters ....... 265
75. Removing a node canister ....... 279
76. Power LEDs on a node canister ..... 280
77. Node canister LEDs ......... 281
78. Replacing the canister cover ...... 286
© Copyright IBM Corp. 2011, 2015 vii
To Next Page
Loading...
Need help?
General
