EasyManuals Logo

Keysight Technologies InfiniiVision MSO-X 4154A User Manual

Keysight Technologies InfiniiVision MSO-X 4154A
1762 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1757 background imageLoading...
Page #1757 background image
Index
Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide 1757
RS-232/UART triggering, 854
R-sense resistor value, N2825A
user-defined R-sense head, 358
RST (Reset), 244
rules, tree traversal, 1615
rules, truncation, 1612
run, 252, 291
Run bit, 280, 283
run count, current harmonics analysis, 743
run mode, mask test, 684
run, USB 2.0 signal quality test, 370
running configuration, 247, 1277
RUNT SEARch commands, 1170
runt search polarity, 1171
runt search qualifier, 1172
runt search source, 1173
runt search, pulse time, 1174
RUNT trigger commands, 1360
runt trigger polarity, 1361
runt trigger qualifier, 1362
runt trigger source, 1363
runt trigger time, 1364
Rx frame count (UART), 1098
Rx source, 1103
S
S and E or U value, USB search, 1258
S and E or U value, USB trigger, 1136
sample rate, 3, 316
Sample Rate, FFT, 481
sample rate, setting (Digitizer mode), 316
sampled data, 1504
sampled data points, 1403
SAV (Save), 247
save, 247, 824
save arbitrary waveform, 825
SAVE commands, 821
save current harmonics analysis
results, 836
save filename, 827
save image, 828
save image with inksaver, 831
save mask, 833, 834
save mask test failures, 687
save path information, 837
save reference waveform, 851
save setup, 844
save to reference waveform location, 1486
save waveform data, 845
saved image, area, 1542
saving and recalling data, 403
SBUS A429 commands, 858
SBUS CAN commands, 877
SBUS commands, 853
SBUS CXPI commands, 907
SBUS I2S commands, 943
SBUS MANChester commands, 999
SBUS NRZ commands, 1018
SBUS SENT commands, 1037
SBUS USBPd commands, 1137
SBUS<n> commands, general, 855
SC value, USB search, 1257
SC value, USB trigger, 1135
scale, 496, 1289, 1293
scale factors output on hardcopy, 508, 829
scale for channels, 364
scale units for channels, 365
scale units for external trigger, 437
scaling display factors, 354
SCPI commands, 89
SCPI.NET example in C#, 1726
SCPI.NET example in IronPython, 1738
SCPI.NET example in Visual Basic
.NET, 1732
SCPI.NET examples, 1726
scratch measurements, 1519
screen area for hardcopy print, 506
screen area for saved image, 1542
screen display of logged remote commands,
enable/disable, 1272
screen image data, 412, 521
SDI pattern, ARINC 429 trigger, 872, 1184
SEARch commands, 1149
SEARch commands, A429, 1180
SEARch commands, CAN, 1186
SEARch commands, EDGE, 1155
SEARch commands, FLEXray, 1196
SEARch commands, general, 1150
SEARch commands, GLITch, 1158
SEARch commands, I2S, 1202
SEARch commands, IIC, 1208
SEARch commands, LIN, 1215
SEARch commands, M1553, 1224
SEARch commands, PEAK, 1165
SEARch commands, RUNT, 1170
SEARch commands, SENT, 1228
SEARch commands, SPI, 1233
SEARch commands, TRANsition, 1175
SEARch commands, UART, 1237
SEARch commands, USB, 1241
search event (found) times, saving, 842
search for found event, 1152
search mode, 1153
search state, 1154
search, edge slope, 1156
search, edge source, 1157
search, USB, 1243
SECAM, 1377, 1381
seconds per division, 1289
segmented memory acquisition times, 843
segmented waveform save option, 849
segments, analyze, 311
segments, count of waveform, 1414
segments, setting number of memory, 312
segments, setting the index, 313
segments, time tag, 1415
select measurement channel, 615
self-test, 253
sensing a channel probe,
1503
sensing a external trigger probe, 1507
sensitivity of oscilloscope input, 354
SENT demo signal, 389
SENT enhanced serial message ID and data
lengths, 1071
SENT fast channel data search value, 1229
SENT fast channel data trigger
setting, 1066
SENT FAST data, 1421
SENT input source, 1061
SENT percent tolerance variation
trigger, 1072
SENT SEARch commands, 1228
SENT search mode, 1230
SENT serial bus commands, 1037
SENT signal length setting, 1051
SENT signals display setting, 1050
SENT slow channel data search
value, 1231
SENT slow channel ID and data trigger data
setting, 1067
SENT slow channel ID search value, 1232
SENT slow channel ID trigger setting, 1069
SENT SLOW data, 1421
SENT trigger mode, 1064
SENT triggering, 854
sequential commands, 91
serial clock, 965, 1080
serial data, 966
serial decode bus, 853
serial decode bus display, 856
serial decode mode, 857
serial frame, 1081
serial number, 292
service request, 251
Service Request Enable Register
(SRE), 249, 1564
set center frequency, 471
set cursors, 1524, 1525
set date, 1261
set time, 1279
set up oscilloscope, 71
setting digital display, 395
setting digital label, 328, 396
setting digital position, 397
setting digital threshold, 399
setting display, 469
setting external trigger level, 433
setting impedance for channels, 350
setting inversion for channels, 351
setting pod display, 701
setting pod size, 702
setting pod threshold, 703
settings, 243, 247
settings conflict errors, 281, 284, 1571,
1573
settings, instrument, 504
setup, 301, 322, 345, 394, 403, 504,
1277
setup and hold trigger clock source, 1367
setup and hold trigger data source, 1368
setup and hold trigger hold time, 1369
setup and hold trigger setup time, 1370
setup and hold trigger slope, 1366
setup configuration, 243, 247, 1277

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Keysight Technologies InfiniiVision MSO-X 4154A and is the answer not in the manual?

Keysight Technologies InfiniiVision MSO-X 4154A Specifications

General IconGeneral
BrandKeysight Technologies
ModelInfiniiVision MSO-X 4154A
CategoryTest Equipment
LanguageEnglish

Related product manuals