Index
Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide 1573
positive slope, 933, 1168
positive slope, Nth edge in burst, 1161
positive TV trigger polarity, 1218
positive width, 522
power analysis, enabling, 641
POWer commands, 619
power factor, 565
power factor for IEC 61000-3-2 Standard
Class C, 647
power loss, 571
power phase angle, 559
power quality analysis, 679
power supply rejection ratio (PSRR), 668,
670, 671
Power Supply Rejection Ratio (PSRR) power
analysis settings, 667
preamble data, 1250
preamble metadata, 1235
predefined logic threshold, 1336
predefined threshold voltages, 1382
present working directory, recall
operations, 720
present working directory, save
operations, 739
preset conditions, 1109
preshoot measured on waveform, 521
previously stored configuration, 211
print command, 255
print job, start, 445
print mask test failures, 600
print query, 1375
printer driver for hardcopy, 1353
printer, active, 432
printing, 430
printing in grayscale, 1351
probe, 1166
probe attenuation affects channel voltage
range, 320
probe attenuation factor (external
trigger), 385
probe attenuation factor for selected
channel, 311
probe head type, 312
probe ID, 313
probe sense for oscilloscope, 1339, 1343
probe skew value, 316, 1337
process sigma, mask test run, 603
program data, 1430
program data syntax rules, 1432
program initialization, 70
program message, 73, 200
program message syntax, 1429
program message terminator, 1430
program structure, 70
programming examples, 6, 1437
protecting against calibration, 295
protection, 251, 253, 319
protection lock, 1112
PTYPE byte (CXPI), trigger when
present, 816
PTYPE frames, CXPI, 813
pulse waveform generator output, 1283
pulse width, 514, 522
pulse width duration trigger, 1172, 1173,
1177
pulse width measurement, 71, 488
pulse width trigger, 1149
pulse width trigger level, 1174
pulse width triggering, 1140
pulse width, waveform generator, 1286
pwidth, 522
Python, VISA COM example, 1464
Python, VISA example, 1511, 1517
PyVISA 1.5 and older, 1511
PyVISA 1.6 and newer, 1517
Q
qualifier, 1177
qualifier for glitch search, 1006
qualifier, runt search, 1016
qualifier, runt trigger, 1201
qualifier, transition search, 1020
qualifier, transition trigger, 1211
qualifier, trigger duration, 1195, 1196
qualifier, trigger pattern, 1197
queries, multiple, 79
query error detected in Standard Event
Status, 205
query responses, block data, 78
query responses, reading, 77
query results, reading into numeric
variables, 78
query results, reading into string
variables, 78
query return values, 1435
query setup, 430, 453, 488, 1120
query subsystem, 280, 352
querying setup, 303
querying the subsystem, 1140
queues, clearing, 1414
quick reference, commands, 83
quoted ASCII string, 194
QYE (Query Error) status bit, 203, 205
R
ramp symmetry, waveform generator, 1287
ramp symmetry, waveform generator
modulating signal, 1296
ramp waveform generator output, 1283
range, 393, 1136
range for channels, 320
range for duration trigger, 1198
range for external trigger, 386
range for full-scale vertical axis, 420
range for glitch search, 1007
range for glitch trigger, 1177
range for time base, 1129
range of offset values, 310
range qualifier, 1176
range, I2S, 858
ranges, value, 194
rate, 275
ratio measurements with X cursors, 463
ratio measurements with Y cursors, 470
ratio of AC RMS values measured between
channels, 547
Ratio, power modulation analysis, 660
raw acquisition record, 1248
RCL (Recall), 211
Rds (dynamic ON resistance)
waveform, 703
Rds(on) power measurement, 572
Rds(on) value for conduction
calculation, 705
reactive power, 573
read configuration, 207
ReadIEEEBlock method, 73, 77, 79
ReadList method, 73, 77
ReadNumber method, 73, 77
readout, 1356
ReadString method, 73, 77
real power, 574
Real Power source in Class D harmonics
analysis, 648
real-time acquisition mode, 267
recall, 211, 714, 1120
recall arbitrary waveform, 715
recall CAN symbolic data, 716
RECall commands, 713
recall filename, 717
, 1281
recall LIN symbolic data, 718
recall mask, 719
recall path information, 720
recall reference waveform, 722
recall setup, 721
recalling and saving data, 360
receiver width, I2S, 848
RECTangular window for transient
signals, 409
reference, 393
reference clock, 1130
reference for time base, 1381
reference point, FFT Phase, 406
reference signal (10 MHz), 269
reference signal mode, 1130
reference waveform save source, 752
reference waveform, recall, 722
reference waveform, save, 753
reference waveforms, clear, 1319
reference waveforms, display, 1320
reference waveforms, label, 1321
reference waveforms, save to, 1322
reference waveforms, skew, 1323
reference waveforms, Y offset, 1324
reference waveforms, Y range, 1325
reference waveforms, Y scale, 1326
reference, lister, 450
reference, time base, 1131
registers, 204, 211, 215, 228, 241, 243,
245, 247, 249, 251, 253
registers, clearing, 1414
reject filter, 1167
To Next Page
Loading...
