D-Link DGS-3000 - Page 98

DGS-3000 Series Layer 2 Managed Gigabit Ethernet Switch CLI Reference Guide
94
offset_chunk_2 - (Optional) Specify the value of the packet bytes to be matched. Offset
chunk 2 will be used.
<hex 0x0-0xffffffff> - Enter the offset chunk 2 mask here.
offset_chunk_3 - (Optional) Specify the value of the packet bytes to be matched. Offset
chunk 3 will be used.
<hex 0x0-0xffffffff> - Enter the offset chunk 3 mask here.
offset_chunk_4 - (Optional) Specify the value of the packet bytes to be matched. Offset
chunk 4 will be used.
<hex 0x0-0xffffffff> - Enter the offset chunk 4 mask here.
ipv6 - Specify that the rule applies to IPv6 fields.
class - (Optional) Specify the value of the IPv6 class.
<value 0-255> - Enter the IPv6 class value here. This value must be between 0 and 255.
flowlabel - (Optional) Specify the value of the IPv6 flow label.
<hex 0x0-0xffff> - Enter the IPv6 flow label mask used here.
source_ipv6 - (Optional) Specify the value of the IPv6 source address.
<ipv6addr> - Enter the source IPv6 address used for this configuration here.
mask - (Optional) Specify an additional mask parameter that can be configured.
<ipv6mask> - Enter the source IPv6 mask here.
destination_ipv6 - (Optional) Specify the value of the IPv6 destination address.
<ipv6addr> - Enter the destination IPv6 address used for this configuration here.
mask - (Optional) Specify an additional mask parameter that can be configured.
<ipv6mask> - Enter the destination IPv6 mask here.
tcp - (Optional) Specify to configure the TCP parameters.
src_port - Specify the value of the IPv6 Layer 4 TCP source port.
<value 0-65535> - Enter the TCP source port value here. This value must be between
0 and 65535.
mask - Specify an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the TCP source port mask value here.
dst_port - (Optional) Specify the value of the IPv6 Layer 4 TCP destination port.
<value 0-65535> - Enter the TCP destination port value here. This value must be
between 0 and 65535.
mask - Specify an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the TCP destination port mask value here.
udp - (Optional) Specify to configure the UDP parameters.
src_port - Specify the value of the IPv6 Layer 4 UDP source port.
<value 0-65535> - Enter the UDP source port value here. This value must be between
0 and 65535.
mask - Specify an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the UDP source port mask value here.
dst_port - Specify the value of the IPv6 Layer 4 UDP destination port.
<value 0-65535> - Enter the UDP destination port value here. This value must be
between 0 and 65535.
mask - Specify an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the UDP destination port mask value here.
icmp - (Optional) Specify to configure the ICMP parameters used.
type - (Optional) Specify that the rule applies to the value of ICMP type traffic.
<value 0-255> - Enter the ICMP type traffic value here. This value must be between 0
and 255.
code - (Optional) Specify that the rule applies to the value of ICMP code traffic.
<value 0-255> - Enter the ICMP code traffic value here. This value must be between 0
and 255.
port - Specify the port list used for this configuration.
<portlist> - Enter a list of ports used for the configuration here.
all - Specify that all the ports will be used for this configuration.
vlan_based - Specify that the rule will be VLAN based.
vlan - Specify the VLAN name used for this configuration.
<vlan_name> - Enter the VLAN name used for this configuration here.
vlan_id - Specify the VLAN ID used for this configuration.
<vlanid 1-4094> - Enter the VLAN ID used here. This value must be between 1 and
4094.