D-Link DGS-3000 - Chapter 86 TFTP Client Command List

DGS-3000 Series Layer 2 Managed Gigabit Ethernet Switch CLI Reference Guide
817
Chapter 86 TFTP Client Command List
download [firmware_fromTFTP {[<ipaddr> | <ipv6addr> | <domain_name 255>] src_file
<path_filename 64> {dest_file <pathname 64>} {boot_up}} | cfg_fromTFTP{ [<ipaddr> |
<ipv6addr> | <domain_name 255>] src_file <path_filename 64> {dest_file <pathname 64>}}]
upload [cfg_toTFTP {[<ipaddr> | <ipv6addr> | <domain_name 255>] dest_file <path_filename 64>
{src_file <pathname 64>} {[include | exclude | begin] <filter_string 80> {<filter_string 80>
{<filter_string 80>}} {[include | exclude | begin ] <filter_string 80> {<filter_string 80>
{<filter_string 80>}} {[include | exclude | begin ] <filter_string 80> {<filter_string 80>
{<filter_string 80>}}}}}} | log_toTFTP{[<ipaddr> | <ipv6addr> | <domain_name 255>] dest_file
<path_filename 64>} | attack_log_toTFTP {[<ipaddr> | <ipv6addr> | <domain_name 255>]
dest_file <path_filename 64>} | firmware_toTFTP {[<ipaddr> | <ipv6addr> | <domain_name
255>] dest_file <path_filename 64> {src_file <path_filename 64>}}]
config tftp {server <ipaddr> | firmware_file <path_filename 64> | cfg_file <path_filename 64> |
log_file <path_filename 64> | attack_log_file <path_filename 64> | certificate_file
<path_filename 64> | key_file <path_filename 64> | tech_support_file <path_filename 64> |
debug_error_log_file <path_filename 64> | sim_firmware_file <path_filename 64> | sim_cfg_file
<path_filename 64> | sim_log_file <path_filename 64>}
show tftp
download 86-1
Description
This command is used to download a new firmware or a switch configuration file.
Format
download [firmware_fromTFTP {[<ipaddr> | <ipv6addr> | <domain_name 255>] src_file
<path_filename 64> {dest_file <pathname 64>} {boot_up}} | cfg_fromTFTP{[<ipaddr> |
<ipv6addr> | <domain_name 255>] src_file <path_filename 64> {dest_file <pathname 64>}}]
Parameters
firmware_fromTFTP - Download and install new firmware on the switch from a TFTP server.
<ipaddr> - (Optional) Enter the IP address of the TFTP server.
<ipv6addr> - (Optional) Enter the IPv6 address of the TFTP server.
<domain_name 255> - (Optional) Enter the domain name of the TFTP server. This name can
be up to 255 characters long.
src_file – (Optional) Specify the path name and file name of the TFTP server. It can be a
relative path name or an absolute path name. If path name is not specified, it refers to the
TFTP server path. The maximum length is 64 characters.
<path_filename 64> - Enter the path name and file name of the TFTP server. It can be a
relative path name or an absolute path name. If path name is not specified, it refers to
the TFTP server path. The maximum length is 64 characters.
dest_file - (Optional) Specify an absolute path name on the device file system. If path name is
not specified, it overwrites the boot-up image on the Switch.
<pathname 64> - Enter an absolute path name on the device file system.
boot_up - (Optional) Specify as boot-up file.
cfg_fromTFTP - Download and install new configuration file on the switch from a TFTP server.
<ipaddr> - (Optional) Enter the IP address of the TFTP server.
<ipv6addr> - (Optional) Enter the IPv6 address of the TFTP server.
<domain_name 255> - (Optional) Enter the domain name of the TFTP server. This name can
be up to 255 characters long.