Index 307
Command 966 - Enable/Disable Automatic Stepping.115
Answering Machine Bypass Only When Armed... 153
Command 999 - Display Panel Type/Software Version
Bell 103 For FSK Format ....................................... 153
.................................................................................117
Disable Dialler Reporting Functions ...................... 153
Communciation Fail......................................................54
Remote Arming Via Telephone.............................. 153
Component Overlay ....................................................263
Dialler Options 2
Connections Of Split EOL Using N/O Contacts .........168
Delay Siren Until Transmission Complete ............. 154
Connections Of Split EOL With Tamper Circuit........167
Extend Time To Wait For Handshake.................... 154
Consumer Options 1....................................................231
Open/Close Reports In STAY Mode...................... 154
Auto Arm In STAY Mode 1 ...................................231
Open/Close Reports Only If Previous Alarm Has
Enable STAY Indicator To Display Day Alarm Status
Occurred ............................................................. 154
............................................................................231
Dialler Options 3
Send Test Report After Siren Reset ........................231
Change Decadic Dialling To 60/40 ........................ 155
Send Test Reports Only If Armed...........................231
Modem Module Required For FSK........................ 155
Consumer Options 2....................................................232
Set DTMF Dialling Pulses To 1 Digit/Second ....... 155
Alarm Memory Reset On Disarm ...........................232
Dialler Reporting Formats.......................................... 130
Enable Codepad Extinguish Mode..........................232
Dialling Format .......................................................... 145
Single Button Arming .............................................232
Disable Factory Default.............................................. 118
Single Button Disarming.........................................232
Disarmed .................................................................... 259
Consumer Options 3
Disarming
Codepad Fault Alarm Beeps ...................................233
Automatic ............................................................... 221
Operation Of Siren & Strobe In STAY Mode.........233
Both Areas At Same Time.................................. 76, 92
Use Digit 3 For Duress Instead Of Digit 9..............233
From AWAY Mode.................................................. 41
Contact ID Format ......................................................130
From STAY Mode 1................................................. 44
Control Panel To Power Up Disarmed........................230
From STAY Mode 2................................................. 46
Copy Control Panel Memory To Programming Key ..111
Single Button Operation ......................................... 232
Copy From Programming Key To Control Panel .......112
Domestic Dialling
Acknowledging Alarm Report................................ 126
D
Changing Domestic Telephone Numbers........... 66, 81
Date and Time.................................................53, 89, 223
Command 965 ........................................................ 114
Day Alarm...........................................................164, 259
Disable.....................67, 69, 70, 72, 82, 84, 85, 87, 128
Latching ..................................................................164
Format .................................................................... 126
Operation.................................................................165
Function.................................................................. 126
Resetting .................................................................164
Setting Up & Programming.................................... 127
Status Indicator .......................................................231
DTMF Dialling Pulses To 1 Digit/Sec ....................... 155
Turning On/Off .........................................................95
Dual Reporting ........................................................... 259
Decadic Dialling To 60/40..........................................155
Duress Alarm................................................................ 47
Defaulting The Control Panel .............................110, 119
E
Delay Alarm Reporting Time......................................217
Delay Siren Until Transmission Complete..................154
E2 Fault ........................................................................ 53
Delete
EDM Smart Watch ..................................................... 227
RF Zones...................................................................64
EDMSAT.............................................. 72, 202, 254, 259
Detectors .....................................................................259
Entry Guard Timer For STAY Mode ............. 42, 45, 217
Dialler .........................................................................259
Entry Time.................................................................. 259
Dialler Information
Entry Timer 1 ............................................................. 216
Answering Machine Bypass....................................148
Entry Timer 2 ............................................................. 216
Call Back Telephone Number.................................147
Entry Warning............................................................ 259
Dialling Format .......................................................145
EOL Resistor Value.................................................... 166
Handshake Tone For Receiver 1 .............................140
Erase Programming Key............................................. 113
Handshake Tone For Receiver 2 .............................143
Event Memory Recall Mode................................... 75, 91
Primary Telephone Number For Receiver 1 ...........139
Exit Installer's Programming Mode............................ 110
Primary Telephone Number For Receiver 2 ...........142
Exit Time............................................................ 217, 260
Programing Telephone Numbers ............................138
External Equipment .................................................... 260
Ring Count ..............................................................148
F
Secondary Telephone Number For Receiver 1 .......139
Secondary Telephone Number For Receiver 2 .......142
Fault
Subscriber ID Number For Receiver 1....................141
AC Mains Failure ..................................................... 54
Subscriber ID Number For Receiver 2....................144
Beeps ...................................................................... 233
Telco Arming Sequence..........................................146
Fault Analysis............................................................... 51
Telco Disarming Sequence .....................................147
Determine Fault Type............................................... 51
Telephone Line Fault Options.................................149
Fault Analysis Mode
Transmission Format For Receiver 1 ......................141
Determine Type ........................................................ 95
Transmission Format For Receiver 2 ......................144
Exit ........................................................................... 95
Dialler Options 1
Fault Descriptions......................................................... 53
Allow Dialler Reporting Functions .........................153
Communciation Fail ................................................. 54
Electronics Design and Manufacturing Pty Limited ISSUE162.DOC
To Next Page
Loading...