310
Solution Ultima 844/862/880 Installation Manual
Normally Open, Pulsing Low ................................. 211
Output Not Used.....................................................211
Outputs ....................................................................... 200
One Shot Polarities ................................................. 214
Polarity ................................................................... 211
Pulsing Polarities .................................................... 213
Redirecting Output To Codepad Buzzer................. 201
Timing .................................................................... 213
Turning On/Off.........................................................87
P
Panic ........................................................................... 260
Panic Alarm .................................................................. 47
PARTIAL Indicator.............................................. 36, 237
Partitioning
Area Addressable Codepad Operations .................. 240
Codepad Operations................................................ 240
Master Partitioned Codepad Operations ................. 240
Master Partitioned LED Codepad........................... 236
Programming ..........................................................241
Setting Up Area 1 Codepad .................................... 246
Setting Up Area 2 Codepad .................................... 246
Setting Up Master Partitioned Codepad ................. 246
User Code Allocations............................................245
Zone Allocations..................................................... 243
Partitioning Options 1
Display AUX Indicator When Using Telephone Line
............................................................................242
First To Open/Last To Close Reporting.................. 241
Main Codepad To Display Data Only For Area 1 .. 241
Resetting Of Sirens From Either Area....................242
Partitioning Options 2
Enable "User Code + 0 + AWAY" To Arm/Disarm
Both Areas .......................................................... 242
Lock Area 1 To Receiver 1 & Lock Area 2 To
Receiver 2...........................................................242
Phone Controller................................................. 255, 260
Plug Pack .................................................................... 256
Point ID Codes............................................................ 131
Power Up Disarmed.................................................... 230
Primary Telephone Number For Receiver 1...............139
Primary Telephone Number For Receiver 2...............142
Programming .............................................................. 102
Automatic Stepping Of Locations .......................... 115
Codepad Indicators ................................................. 103
Entry/Exit Tiemrs ................................................... 216
Installer's Programming Commands....................... 107
Option Bits.............................................. 107, 152, 226
Telephone Numbers................................................ 138
Via Hand Held Programmer ................................... 105
Via Programming Key............................................ 106
Via Remote Codepad..............................................103
Programming Key............................................... 106, 254
Copy From Programming Key To Panel ................ 112
Copy Panel Memory To Programming Key ........... 111
Erase ....................................................................... 113
Test .........................................................................109
Programming Sheets
Solution 404............................................................ 275
Solution 406............................................................ 285
Solution 408............................................................ 295
PS100 Power Supply Module..................................... 255
Q
Quick Start ....................................................................22
R
Radio Input Options ....................................................234
Latching Keyswitch Input .......................................234
Momentary Keyswitch Input...................................234
Radio Receiver........................................................234
Radio Key/Keyswitch Interface ..........................230, 256
Radio User Codes
Transmitter Operations..............................................56
Receiver 1
Handshake Tone......................................................140
Primary Telephone Number ....................................139
Secondary Telephone Number ................................139
Subscriber ID Number ............................................141
Transmission Format...............................................141
Receiver 2
Handshake Tone......................................................143
Primary Telephone Number ....................................142
Secondary Telephone Number ................................142
Subscriber ID Number ............................................144
Transmission Format...............................................144
Relay Output ...............................................................200
Remote Arming Via Telephone ..........................100, 153
Remote Radio Transmitter Operations..........................56
Add or Changing Transmitter Codes...................58, 79
Deleting Transmitter Codes ................................59, 80
Horn Speaker Beeps..................................................57
Strobe Indications......................................................57
Remote Radio User Codes
Adding Or Changing ...........................................58, 79
Deleting...............................................................59, 80
Reporting Format
4 + 2 Reporting Format ...........................................133
Basic Pager..............................................................134
Contact ID Format...................................................130
Domestic Dialling ...................................................126
Reset Control Panel Back To Factory Default ............110
RF
Device Mapping (1 - 8) ...........................................250
Device Mapping (9 - 16) .........................................250
Device Signal Strength (1 - 8).................................251
Dialler Reporting Options .......................................188
Jamming Monitoring...............................................250
Low Battery.............................................................187
Receiver Trouble Report .........................................188
Receiver Trouble Restore Report............................188
Sound Siren On RF Receiver Fail ...........................250
Sound Siren On RF Receiver Tamper/Jamming .....250
Supervision Time ....................................................187
Unseal Zone That Fails Supervision .......................250
RF Low Battery.............................................................53
RF Receiver Fail ...........................................................53
RF Transmitter Operations............................................56
RF Zones
Add............................................................................63
Delete ........................................................................64
Ring Burst Time..........................................................150
Ring Count ..................................................................148
S
Satellite Siren ......................................................254, 259
ISSUE162.DOC Electronics Design and Manufacturing Pty Limited
To Next Page
Loading...