Compliance Information—
L160-Specic
L160 UL Labels
MODEL 1FINITYâ„¢ L160 BDL1-3M21
PART NO. FC95453M21 Iss. 01
SER NO. H0001 DATE YYYY–M
MADE IN CHINA
FUJITSU LIMITED
HOLD HERE
HOLD HERE
CAUTION: RISK OF ELECTRIC SHOCK.
THIS EQUIPMENT HAS DUAL 48V INPUTS.
BOTH MUST BE DISCONNECTED TO
DE-ENERGIZE EQUIPMENT.
CAUTION: HAZARD LEVEL 1M LASER RADIATION.
DO NOT VIEW WITH NON-ATTENUATING OPTICAL
INSTRUMENTS.
ATTENTION: NIVEAU DE RISQUE DE
RAYONNEMENT LASER 1M NE
PAS. REGARDER DIRECTEMENT SANS
CAUTION:
SEE INSTALLATION
MANUAL BEFORE
INSTALLING.
ATTENTION:
VOIR MANUEL
D’ INSTALLATION
AVANT
Ľ INSTALLATION.
ATTENTION: RISQUE DE CHOC
ÉLECTRIQUE. CET ÉQUIPEMENT REÇOIT
PLUSIEURS ALIMENTATIONS. COUPER
LE COURANT AVANT Ľ ENTRETIEN.
CAN ICES-3 (A) /NMB-3 (A)
CONDITIONS OF ACCEPTABILITY:
TO BE INSTALLED ONLY IN RESTRICTED
ACCESS LOCATIONS IN ACCORDANCE WITH
THE NEC, CAN ICES-3A AND ANSI/NFPA NO. 70.
MATERIEL À INSTALLER UNIQUEMENT DANS DES
LIEUX À ACCÈS RESTREINT CONFORMÉMENT À LA
NORME NEC, CAN ICES-3A ET ANSI/NFPA NO. 70.
THIS EQUIPMENT COMPLIES WITH PART 15 OF THE
FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING CONDITIONS:
(1) THIS MAY NOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS MUST ACCEPT ANY INTERFERENCE
RECEIVED INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
USE COPPER CONDUCTORS ONLY.
Manufactured
2019, November
Micro PDF417
Class I Laser Product
Conformé à 21 CFR
MOLEX, LLC
46360 Fremont Blvd,
Fremont, CA 94538. USA
FC95453M21
Iss. 01
LBFJTU291865453M2101H0001
WOMSW10DRA
QR
MOLEX
Molex PN: 1835260000
FUJITSU PN: TA09068–C130
Weight:
Poids:
19.8 lb
9.0 kg
19.8 lb
9.0 kg
Complies with 21 CFR 1040.10 and
1040.11 except for conformance
with IEC 60825-1 Ed. 3, as described
in Laser Notice No. 56, dated
May 8, 2019.
FNC001299_Rev_01
UL Fuse Rangs
Model/Type Reference Rang
L160 (BDL1-3M21) –48 V DC
General Compliance
â– NEBS Level 3:
• GR-63-CORE Issue 05 (including Seismic Zone 4
requirements)
• GR-1089-Electromagnec Compability (EMC) and Electrical
Safety
• GR-3108-Class 1-Equipment in the Outside Plant (OSP)
■GR-1089, Secon 9 (Bonding and Grounding) required
installaon standards:
• Installed in a Common Bonding Network (CBN)
• Installed in NEBS Level 3 environments, for example, Central
Oces as well as Customer Premise Environment (CPE)
• Installed in accordance with a DC-C or DC-I conguraon
■GR-1089, R4-16, R4-18 (Intra-Building Lightning Protecon)
Warning: All metallic signaling cables
should be shielded with the shield
grounded at both ends to meet intra-
building lightning requirements.
Warning: The intra-building port(s)
(UTLP1, UTLP2, and MAINT) of the
equipment or subassembly is suitable for
connecon to intra-building or
unexposed wiring or cabling only. The
intra-building port(s) of the equipment
or assembly MUST NOT be metallically
connected to interfaces that connect to
the OSP or its wiring. These interfaces
are designed for use as intra-building
interfaces only (Type 2 or Type 4 ports)
as described in GR-1089 and required
isolaon from the exposed ODP cabling.
The addion of Primary Protectors is not
sucient protecon to connect these
interfaces metallically to OSP wiring.
â– UL/CSA 62368-1
â– The 1FINITY L160 Blade is compliant with the Laser IEC/EN
60825-1, 2 standards.
â– The 1FINITY L160 Blade is compliant with 21 CFR 1040.10 and
1040.11 except for conformance with IEC 60825-1 Ed. 3., as
described in Laser Noce No. 56, dated May 8, 2019., Class 1
Laser Product.
â– The 1FINITY L160 Blade is compliant with the Class A Emission
limits of the following standards:
• FCC Part 15, Class A
• ICES-003
• CISPR Publicaon 32 Class A (Europe)
â– The 1FINITY L160 Blade is approved for the following product
safety regulatory standards:
• CAN/CSA-C22.2 No. 62368-1/UL 62368-1, 2nd Edion,
2014-12-01 (Audio/video, informaon and communicaon
technology equipment—Part 1: Safety requirements)
• IEC 60950-1:2005 (Second Edion); Am1:2009 + Am2:2013
• IEC 62368-1:2014 (Modied) (Audio/video, informaon and
communicaon technology equipment—Part 1: Safety
requirements)
To Next Page
Loading...
Need help?
General