Huawei Quidway S9300

[P-GigabitEthernet1/0/0] port hybrid pvid vlan 30
[P-GigabitEthernet1/0/0] port hybrid untagged vlan 30
[P-GigabitEthernet1/0/0] quit
[P] interface GigabitEthernet 2/0/0
[P-GigabitEthernet2/0/0] port hybrid pvid vlan 60
[P-GigabitEthernet2/0/0] port hybrid untagged vlan 60
[P-GigabitEthernet2/0/0] quit
[P] interface vlanif 30
[P-Vlanif30] ip address 172.1.1.2 24
[P-Vlanif30] quit
[P] interface vlanif 60
[P-Vlanif60] ip address 172.2.1.1 24
[P-Vlanif60] quit
[P] ospf
[P-ospf-1] area 0
[P-ospf-1-area-0.0.0.0] network 172.1.1.0 0.0.0.255
[P-ospf-1-area-0.0.0.0] network 172.2.1.0 0.0.0.255
[P-ospf-1-area-0.0.0.0] network 2.2.2.9 0.0.0.0
[P-ospf-1-area-0.0.0.0] quit
[P-ospf-1] quit
# Configure PE2.
<Quidway> system-view
[Quidway] sysname PE2
[PE2] interface loopback 1
[PE2-LoopBack1] ip address 3.3.3.9 32
[PE2-LoopBack1] quit
[PE2] vlan 40
[PE2-vlan40] port GigabitEthernet 1/0/0
[PE2-vlan40] quit
[PE2] vlan 50
[PE2-vlan50] port GigabitEthernet 2/0/0
[PE2-vlan50] quit
[PE2] vlan 60
[PE2-vlan60] port GigabitEthernet 3/0/0
[PE2-vlan60] quit
[PE2] interface vlanif 60
[PE2-Vlanif20] ip address 172.2.1.2 24
[PE2-Vlanif20] quit
[PE2] ospf
[PE2-ospf-1] area 0
[PE2-ospf-1-area-0.0.0.0] network 172.2.1.0 0.0.0.255
[PE2-ospf-1-area-0.0.0.0] network 3.3.3.9 0.0.0.0
[PE2-ospf-1-area-0.0.0.0] quit
[PE2-ospf-1] quit
After the configuration, OSPF adjacencies are established between PE1, P, and PE2. By running
the display ospf peer command, you can see that the status of the OSPF adjacency is Full. By
running the display ip routing-table command, you can see that the PEs can learn the routes
of each other's Loopback1 interface.
Take PE1 for example.
[PE1] display ip routing-table
Route Flags: R - relied, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 9 Routes : 9
Destination/Mask Proto Pre Cost Flags NextHop Interface
1.1.1.9/32 Direct 0 0 D 127.0.0.1 InLoopBack0
2.2.2.9/32 OSPF 10 1 D 172.1.1.2 Vlanif30
3.3.3.9/32 OSPF 10 2 D 172.1.1.2 Vlanif30
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.1.1.0/24 Direct 0 0 D 172.1.1.1 Vlanif30
Quidway S9300 Terabit Routing Switch
Configuration Guide - VPN 3 BGP/MPLS IP VPN Configuration
Issue 03 (2009-08-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3-59