EasyManuals Logo

Huawei Quidway S9300 Configuration Guide

Huawei Quidway S9300
567 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #77 background imageLoading...
Page #77 background image
Run the display ip routing-table command, and you can see that the routing table contains the
route passing through the tunnel interface. The following is an example:
<Quidway> display ip routing-table
Route Flags: R - relied, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 11 Routes : 11
Destination/Mask Proto Pre Cost Flags NextHop Interface
10.1.1.0/24 Direct 0 0 D 10.1.1.2 Vlanif20
10.1.1.2/32 Direct 0 0 D 127.0.0.1 InLoopBack0
10.2.1.0/24 Static 60 0 D 40.1.1.1 Tunnel1/0/1
20.1.1.0/24 Direct 0 0 D 20.1.1.1 Vlanif10
20.1.1.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
20.1.1.2/32 Direct 0 0 D 20.1.1.2 Vlanif10
30.1.1.0/24 OSPF 10 2 D 20.1.1.2 Vlanif10
40.1.1.0/24 Direct 0 0 D 40.1.1.1 Tunnel1/0/1
40.1.1.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
Run the ping -a source-ip-address dest-ip-address command, and you can see that the local
tunnel interface can ping the destination tunnel interface.
2.4 Configuring a GRE Tunnel Between CE and PE
This section describes how to configure a CE to access the public network by using a GRE
tunnel.
2.4.1 Establishing the Configuration Task
2.4.2 Configuring the GRE Tunnel Interface on CE
2.4.3 Configuring the GRE Tunnel Interface on PE
2.4.4 Binding the Tunnel with VPN to Which CE belongs on PE
2.4.5 Checking the Configuration
2.4.1 Establishing the Configuration Task
Applicable Environment
To allow users of the CE that is not directly connected with a PE to access the Multi-Protocol
Label Switching (MPLS) VPN, configure a GRE tunnel and create routes between them and
configure MPLS VPN on the PE.
Pre-configuration Tasks
Before configuring a GRE tunnel between a CE and a PE, complete the following tasks:
l Assigning IP addresses for interfaces on the CE and PE
l Configuring the routes between the CE and PE
Data Preparation
To configure a GRE tunnel between a CE and a PE, you need the following data.
Quidway S9300 Terabit Routing Switch
Configuration Guide - VPN 2 GRE Configuration
Issue 03 (2009-08-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
2-7

Table of Contents

Other manuals for Huawei Quidway S9300

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Huawei Quidway S9300 and is the answer not in the manual?

Huawei Quidway S9300 Specifications

General IconGeneral
BrandHuawei
ModelQuidway S9300
CategoryNetwork Router
LanguageEnglish

Related product manuals