Huawei Quidway S9300

local VCCV : cw lsp-ping
remote VCCV : cw lsp-ping
local control word : enable remote control word : enable
tunnel policy name : --
traffic behavior name : --
PW template name : pwt
primary or secondary : primary
VC tunnel/token info : 1 tunnels/tokens
NO.0 TNL type : lsp , TNL ID : 0x20020
create time : 0 days, 0 hours, 15 minutes, 3 seconds
up time : 0 days, 0 hours, 3 minutes, 15 seconds
last change time : 0 days, 0 hours, 3 minutes, 15 seconds
Display the status of the switching L2VC on S-PE.
<S-PE> display mpls switch-l2vc
Total Switch VC : 1, 1 up, 0 down
*Switch-l2vc type : LDP<---->LDP
Peer IP Address : 5.5.5.9, 1.1.1.9
VC ID : 200, 100
VC Type : VLAN
VC State : up
VC StatusCode |PSN |OAM | FW | |PSN |OAM | FW |
-Local VC :| UP | UP | UP | | UP | UP | UP |
-Remote VC:| UP | UP | UP | | UP | UP | UP |
Session State : up, up
Local/Remote Label : 21504/21504, 21505/21504
Local/Remote MTU : 1500/1500, 1500/1500
Local/Remote Control Word : Enable/Enable, Enable/Enable
Local/Remote VCCV Capability : cw lsp-ping/cw lsp-ping, cw lsp-ping/cw lsp-ping
Switch-l2vc tunnel info :
1 tunnels for peer 5.5.5.9
NO.0 TNL Type : lsp , TNL ID : 0X20026
1 tunnels for peer 1.1.1.9
NO.0 TNL Type : lsp , TNL ID : 0x10020
Create time : 0 days, 0 hours, 13 minutes, 1 seconds
UP time : 0 days, 0 hours, 3 minutes, 58 seconds
Last change time : 0 days, 0 hours, 3 minutes, 58 seconds
Step 9 Verify the connectivity of the PW.
Run the ping vc command on the U-PE, and you can see that the connectivity of the PW is
normal. Take the display on U-PE1 for example.
<U-PE1> ping vc vlan 100 control-word remote 200
Reply: bytes=100 Sequence=1 time = 740 ms
Reply: bytes=100 Sequence=2 time = 90 ms
Reply: bytes=100 Sequence=3 time = 160 ms
Reply: bytes=100 Sequence=4 time = 130 ms
Reply: bytes=100 Sequence=5 time = 160 ms
--- FEC: FEC 128 PSEUDOWIRE (NEW). Type = vlan, ID = 100 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 90/256/740 ms
Step 10 Collect path information about the PW.
Run the tracert vc command on the U-PE, and you can collect information about the LSRs
where the PW passes through and the egress PE. Take the display on U-PE1 for example.
<U-PE1> tracert vc vlan 100 control-word remote 200 full-lsp-path
TTL Replier Time Type Downstream
0 Ingress 10.1.1.2/[1025 ]
1 10.1.1.2 100 ms Transit 20.1.1.2/[3 ]
2 20.1.1.2 60 ms Transit
3 30.1.1.2 80 ms Transit 40.1.1.2/[3 ]
5 PWE3 Configuration
Quidway S9300 Terabit Routing Switch
Configuration Guide - VPN
5-60 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Issue 03 (2009-08-20)