Huawei Quidway S9300

remote AC OAM state : up
remote PSN state : up
remote forwarding state: forwarding
BFD for PW : unavailable
manual fault : not set
active state : inactive
forwarding entry : existent
link state : up
local VC MTU : 1500 remote VC MTU : 1500
local VCCV : cw lsp-ping bfd
remote VCCV : cw lsp-ping bfd
local control word : enable remote control word : enable
tunnel policy : --
traffic behavior : --
PW template name : 1to2
primary or secondary : secondary
VC tunnel/token info : 1 tunnels/tokens
NO.0 TNL type : lsp , TNL ID : 0x20021
create time : 0 days, 0 hours, 22 minutes, 19 seconds
up time : 0 days, 0 hours, 1 minutes, 32 seconds
last change time : 0 days, 0 hours, 1 minutes, 32 seconds
reroute policy : delay 30 s, resume 0 s
reason of last reroute : New LDP mapping message was received
time of last reroute : 0 days, 0 hours, 0 minutes, 50 seconds
delay timer ID : -- rest time :--
resume timer ID : -- rest time :--
Client1 can ping 10.1.1.2 on Client2.
[Client] ping 10.1.1.2
PING 10.1.1.2: 56 data bytes, press CTRL_C to break
Reply from 10.1.1.2: bytes=56 Sequence=1 ttl=255 time=180 ms
Reply from 10.1.1.2: bytes=56 Sequence=2 ttl=255 time=150 ms
Reply from 10.1.1.2: bytes=56 Sequence=3 ttl=255 time=150 ms
Reply from 10.1.1.2: bytes=56 Sequence=4 ttl=255 time=190 ms
Reply from 10.1.3.110.1.1.2: bytes=56 Sequence=5 ttl=255 time=160 ms
--- 10.1.1.2 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 150/166/190 ms
Run the display mac-address dynamic command on CEs. Take the display on CE2 for example.
You can see that GE1/0/0 has learned the MAC address of Client1 (00e0-413f-8401) and
GE1/0/2 has learned the MAC address of Client2 (00e0-c279-e10a 10). This indicates that the
clients are using the master link CE2 → PE3 → P → PE1 to forward data.
[CE2] display mac-address dynamic 1
MAC Address VLAN/VSI PEVLAN CEVLAN Port Type Lsp
--------------------------------------------------------------------------------
00e0-413f-8401 10 - - GE1/0/0 dynamic 1/0
00e0-c279-e10a 10 - - GE1/0/2 dynamic 1/0
Total 2 ,2 printed
Step 8 Verify the configuration.
l View the status of PWs.
Run the display mpls l2vc interface command on PE1. If the configuration is successful, you
can see that the master PW is in Active state, the backup PW is in InActive state.
<PE1> display mpls l2vc interface Vlanif 10
*client interface : Vlanif10 is up
session state : up
AC state : up
Quidway S9300 Terabit Routing Switch
Configuration Guide - VPN 5 PWE3 Configuration
Issue 03 (2009-08-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5-83