MacDon D1 Series - Page 22

215184 xx Revision A
Engaging the Auto Header Height Control – Gleaner R65/R66/R75/R76 and Pre-2016 S Series ............... 394
Calibrating the Auto Header Height Control – Gleaner R65/R66/R75/R76 and Pre-2016 S Series............. 396
Turning off the Accumulator – Gleaner R65/R66/R75/R76 and Pre-2016 S Series ................................. 397
Adjusting the Header Raise/Lower Rate – Gleaner R65/R66/R75/R76 and Pre-2016 S Series .................. 398
Adjusting Ground Pressure – Gleaner R65/R66/R75/R76 and Pre-2016 S Series ................................... 398
Adjusting the Sensitivity of the Auto Header Height Control – Gleaner R65/R66/R75/R76 and Pre-2016
S Series....................................................................................................................... 399
Troubleshooting Alarms and Diagnostic Faults – Gleaner R65/R66/R75/R76 and Pre-2016
S Series....................................................................................................................... 400
9.1.13 Gleaner S9 Series Combines ....................................................................................................... 402
Setting up the Header – Gleaner S9 Series .................................................................................... 402
Setting Minimum Reel Speed and Calibrating Reel – Gleaner S9 Series ............................................... 407
Setting up Automatic Header Controls – Gleaner S9 Series............................................................... 409
Calibrating the Header – Gleaner S9 Series.................................................................................... 411
Operating the Header – Gleaner S9 Series..................................................................................... 414
Reviewing Header In-Field Settings – Gleaner S9 Series ................................................................... 415
9.1.14 John Deere 60 Series Combines .................................................................................................. 416
Checking Voltage Range from the Combine Cab – John Deere 60 Series ............................................. 416
Calibrating the Auto Header Height Control – John Deere 60 Series................................................... 419
Turning the Accumulator Off – John Deere 60 Series....................................................................... 421
Setting the Sensing Grain Header Height to 50 – John Deere 60 Series ............................................... 422
Setting the Sensitivity of the Auto Header Height Control – John Deere 60 Series ................................ 423
Adjusting the Threshold for the Drop Rate Valve – John Deere 60 Series ............................................ 424
9.1.15 John Deere 70 Series Combines .................................................................................................. 424
Checking Voltage Range from the Combine Cab – John Deere 70 Series ............................................. 424
Calibrating Feeder House Speed – John Deere 70 Series .................................................................. 428
Calibrating the Auto Header Height Control – John Deere 70 Series................................................... 428
Setting the Sensitivity of the Auto Header Height Control – John Deere 70 Series ................................ 430
Adjusting the Manual Header Raise/Lower Rate
– John Deere 70 Series ............................................. 431
9.1.16 John Deere S and T Series Combines............................................................................................ 431
Checking Voltage Range from the Combine Cab – John Deere S and T Series....................................... 431
Calibrating the Auto Header Height Control – John Deere S and T Series ............................................ 435
Setting the Sensitivity of the Auto Header Height Control – John Deere S and T Series.......................... 438
Adjusting the Manual Header Raise/Lower Rate – John Deere S and T Series ...................................... 439
Setting Preset Cutting Height – John Deere S and T Series................................................................ 440
Calibrating Feeder House Fore-Aft Tilt Range – John Deere S and T Series .......................................... 442
Checking Reel Height Sensor Voltages – John Deere S and T Series .................................................... 445
Calibrating Reel Height Sensor – John Deere S and T Series .............................................................. 447
9.1.17 John Deere S7 Series Combines .................................................................................................. 450
Setting up Header – John Deere S7 Series ..................................................................................... 450
Checking Voltage Range from the Combine Cab – John Deere S7 Series ............................................. 453
Calibrating Feeder House – John Deere S7 Series ........................................................................... 456
Calibrating Header – John Deere S7 Series .................................................................................... 459
9.1.18 New Holland Combines – CR/CX Series – 2014 and Prior ................................................................. 462
Checking Voltage Range from the Combine Cab – New Holland CR/CX Series ...................................... 462
Setting up Auto Header Height Control – New Holland CR/CX Series.................................................. 465
Calibrating the Auto Header Height Control – New Holland CR/CX Series............................................ 466
Calibrating Maximum Stubble Height – New Holland CR/CX Series .................................................... 467
Adjusting Header Raise Rate – New Holland CR/CX Series ................................................................ 469
Setting the Header Lower Rate – New Holland CR/CX Series............................................................. 469
Setting the Sensitivity of the Auto Header Height Control – New Holland CR/CX Series ......................... 470
Setting Preset Cutting Height – New Holland CR/CX Series ............................................................... 471
9.1.19 New Holland Combines – CR Series – 2015 and Later...................................................................... 472
TABLE OF CONTENTS