D-Link DGS-3000 - Page 196

DGS-3000 Series Layer 2 Managed Gigabit Ethernet Switch CLI Reference Guide
192
Parameters
profile_id - Specify the index of access list profile.
<value 1-5> - Enter the profile ID value here. This value must be between 1 and 5.
all - Specify that al the access list profiles will be deleted.
Restrictions
Only Administrators, Operators and Power-Users can issue this command.
Example
To delete CPU access list rules:
DGS-3000-26TC:admin#delete cpu access_profile profile_id 1
Command: delete cpu access_profile profile_id 1
Success.
DGS-3000-26TC:admin#
config cpu access_profile 17-3
Description
This command is used to configure CPU access list entry.
Format
config cpu access_profile profile_id <value 1-5> [add access_id [auto_assign | <value 1-
100>] [ethernet {[vlan <vlan_name 32> | vlan_id <vlanid 1-4094>] | source_mac <macaddr> |
destination_mac <macaddr> | 802.1p <value 0-7> | ethernet_type <hex 0x0-0xffff>} | ip {[vlan
<vlan_name 32> | vlan_id <vlanid 1-4094>] | source_ip <ipaddr> | destination_ip <ipaddr> |
dscp <value 0-63> | [icmp {type <value 0-255> | code <value 0-255>} | igmp {type <value 0-
255>} | tcp {src_port <value 0-65535> | dst_port <value 0-65535> | flag [all | {urg | ack | psh |
rst | syn | fin}]} | udp {src_port <value 0-65535> | dst_port <value 0-65535>} | protocol_id
<value 0-255> {user_define <hex 0x0-0xffffffff>}]} | packet_content {offset_0-15 <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_16-31 <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_32-47 <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_48-63 <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_64-79 <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>} | ipv6 {class <value 0-
255> | flowlabel <hex 0x0-0xfffff> | source_ipv6 <ipv6addr> | destination_ipv6 <ipv6addr>}]
port [<portlist> | all] [permit | deny] {time_range <range_name 32>} | delete access_id
<value 1-100>]
Parameters
profile_id - Specify the index of access list profile.
<value 1-5> - Enter the profile ID value here. This value must be between 1 and 5.
add - Specify that a profile or a rule will be added.
access_id - Specify the index of access list entry. The range of this value is 1-100.
<value 1-100> - Enter the access ID here. This value must be between 1 and 100.
ethernet - Specify that the profile type will be Ethernet.
vlan - (Optional) Specify the VLAN name used.