D-Link DGS-3000 - Page 197

DGS-3000 Series Layer 2 Managed Gigabit Ethernet Switch CLI Reference Guide
193
<vlan_name 32> - Enter the name of the VLAN here. This name can be up to 32
characters long.
vlan_id - (Optional) Specify the VLAN ID used.
<vlanid 1-4094> - Enter the VLAN ID used here.
source_mac - (Optional) Specify the source MAC address.
<macaddr> - Enter the source MAC address used for this configuration here.
destination_mac - (Optional) Specify the destination MAC.
<macaddr> - Enter the destination MAC address used for this configuration here.
802.1p - (Optional) Specify the value of 802.1p priority tag.
<value 0-7> - Enter the 802.1p priority tag value here. This value must be between 0 and
7.
ethernet_type - (Optional) Specify the Ethernet type.
<hex 0x0-0xffff> - Enter the Ethernet type value here.
ip - Specify that the profile type will be IP.
vlan - (Optional) Specify the VLAN name used.
<vlan_name 32> - Enter the name of the VLAN here. This name can be up to 32
characters long.
vlan_id - (Optional) Specify the VLAN ID used.
<vlanid 1-4094> - Enter the VLAN ID used here.
source_ip - (Optional) Specify an IP source address.
<ipaddr> - Enter the source IP address used for this configuration here.
destination_ip - (Optional) Specify an IP destination address.
<ipaddr> - Enter the destination IP address used for this configuration here.
dscp - (Optional) Specify the value of DSCP, the value can be configured 0 to 63.
<value 0-63> - Enter the DSCP value used here.
icmp - (Optional) Specify that the rule applies to ICMP traffic.
type - (Optional) Specify that the rule applies to the value of ICMP type traffic.
<value 0-255> - Enter the ICMP type value here. This value must be between 0 and
255.
code - (Optional) Specify that the rule applies to the value of ICMP code traffic.
<value 0-255> - Enter the ICMP code value here. This value must be between 0 and
255.
igmp - (Optional) Specify that the rule applies to IGMP traffic.
type - (Optional) Specify that the rule applies to the value of IGMP type traffic.
<value 0-255> - Enter the IGMP type value here. This value must be between 0 and
255.
tcp - (Optional) Specify that the rule applies to TCP traffic.
src_port - (Optional) Specify that the rule applies the range of TCP source port.
<value 0-65535> - Enter the source port value here. This value must be between 0 and
65535.
dst_port - (Optional) Specify the range of TCP destination port range.
<value 0-65535> - Enter the destination port value here. This value must be between 0
and 65535.
flag - (Optional) Specify the TCP flag fields .
all - Specify that the TCP flag field mask will be set to all.
urg - (Optional) Specify that the TCP flag field mask will be set to urg.
ack - (Optional) Specify that the TCP flag field mask will be set to ack.
psh - (Optional) Specify that the TCP flag field mask will be set to psh.
rst - (Optional) Specify that the TCP flag field mask will be set to rst.
syn - (Optional) Specify that the TCP flag field mask will be set to syn.
fin - (Optional) Specify that the TCP flag field mask will be set to fin.
udp - Specify that the rule applies to UDP traffic.
src_port - (Optional) Specify the range of UDP source port range.
<value 0-65535> - Enter the source port value here. This value must be between 0 and
65535.
dst_port - (Optional) Specify the range of UDP destination port mask.
<value 0-65535> - Enter the destination port value here. This value must be between 0
and 65535.
protocol_id - Specify that the rule applies to the value of IP protocol ID traffic.
<value 0-255> - Enter the protocol ID value here. This value must be between 0 and 255.