o Added explanation that SkyView can be powered on during engine start
(Page 2-5)
o Recommendation to install Panel Mount USB cable with each SkyView
display (Page 2-6)
o Serial port connection and configuration information for Emergency
Location Transmitter (ELT) (Page 4-20)
o External Dim Control Connections (Page 4-20)
o SV-ADAHRS-200/201 must be installed level or the Slip/Skid Ball will not be
centered (Page 5-3)
o Caution about applying too much torque when installing SV-BAT-320 (Page
9-2)
o Addition of capacitor to servo to eliminate Intercom noise (Page 10-12, 10-
13)
o Pin descriptions, added wiring diagram for SV-AP-PANEL Trim Controller
installation (Section 19)
o As of v11.0, SkyView does not have “Auto-trim” capability (Page 19-3)
o Alert Data Log (Page 26-2)
Documentation improved:
o Getting Started (Pages 1-2 through 1-4)
o SkyView System Power Specifications (Table 2, Page 2-2)
o Corrected SV-XPNDR-261/262 dimensions (Page 2-3)
o Recommendation to not use stainless steel hardware for installing SV-
ADAHRS-200/201, added recommendation to use Brass hardware (Page 2-8,
Page 5-3)
o Explanation of Dynon Avionics Diagnostic File (Page 3-10 and Page 3-16)
o Updated screen shots throughout SV-D700 / SV-D1000 / SV-D1000T
Installation and Configuration (Section 4)
o Moved configuration information for Garmin GTX 330ES to Traffic Devices
section (Page 4-14)
o VAL NAV 2000 – frequency cannot be displayed on top bar (Page 4-17)
o Updated SV-ADAHRS-200/201 Magnetic Calibration Procedure (Page 5-5)
o Differences between SV-EMS-220 and SV-EMS-221 (Page 7-1)
o Rotax oil pressure sensor connector charge (Page 7-41, 7-42)
o Oil temperature sensor section, updated crush washer installation
instructions. (Page 7-42)
o Rotax 914 Differential Fuel Pressure Sensor UMA N1EU07D guidance
improved (Page -7-44, 7-45)
o Suppress units displayed on sensor widgets (Page 7-63)
o Effect of setting ALLOW AUTO SWITCH to YES (LABEL 100P) for 430/530
(Page 12-7) and GTN-series (12-9)
o Setup for transponders other than SV-XPNDR-261/262 with ADS-B OUT for
receiving ADS-B Traffic information with SV-ADSB-470 (Page 14-1)
o Check for blockage of AOA / Pitot lines prior to installation (Page 15-10)
o SV-COM-C25 Post Installation Checks, Continued Airworthiness and
Maintenance (Page 16-8, 16-9)
o Non-Dynon Avionics Wire Harness Considerations (Page 21-2 through 21-4)
o MAP button no longer available (Page 21-11)
o Kavlico pressure sensors information (Appendix G)
401 pages
Document number changed to 101320-018
Software changes in SkyView Software v12.0:
o New: Support for Wi-Fi connectivity to ForeFlight via the new SkyView Wi-Fi
Adapter. Transfer flight plans between SkyView and ForeFlight. Send
SkyView's attitude indication and GPS position to ForeFlight.
o New: Autopilot auto-trim. The SkyView Autopilot can automatically keep
the aircraft in trim as it flies under autopilot control. This feature requires
that the aircraft has an SV-AP-PANEL and is using its integrated trim
controller for electric trim servo actuation. Auto-trim can be configured on
pitch and/or roll axes.
o New: OBS Mode that allows pilots easily set and adjust an inbound course
to any navigable point on the map. That inbound course may then be easily
adjusted with the HSI CRS knob, similar to how one would with a VOR. This
is useful to approach an airport from a specific direction, for example,
without having to create a second waypoint to create a full flight plan leg.
To Next Page
Loading...
