o Corrected reference to connect Rotax oil pressure sensor’s black wire to
Ground (Page 7-43).
o Updated guidance for safe voltage levels applied to General Purpose Inputs,
Contacts (Page 7-7, 7-60, and 7-72).
o Changed recommendation on wiring SV-NET-SERVO Kit to route power,
ground, and servo disconnect wires through DB9 connectors (Page 10-9
through 10-11)
o Section 11 (SV-XPNDR-261/262) extensively rewritten to incorporate SV-
GPS-2020 and SV-GPS-250 SIL/SDA=1.
o Updated guidance / explanation of ICAO / HEX code (Page 11-19)
o Updated Advanced Control Module configuration (Page 15-14)
o Corrected several incorrect references to type of connector required for the
antenna cable: SV-ADSB-470, SV-COM-425, SV-XPNDR-261/262, and SV-
COM-X83.
o Appendix C: Wiring and Electrical Connections extensively rewritten to
incorporate connector diagrams and several missing units.
496 pages
Document number changed to 101320-023, Revision X
Document name changed to SkyView and SkyView SE System Installation Guide
Software changes in SkyView Software v14.1, released 2016-03-29. Added:
o SYSTEM EVENT alerts that enabled SkyView detect additional software
anomalies. Upon seeing a SYSTEM EVENT alert, users should enter the
Setup Menu for more information and instructions.
Software changes in SkyView Software v14.1, released 2016-03-29. Improved:
o Checklist imports with file format problems now shows the error line
numbers.
o Checklists feature has various fixes and improvements
Software changes in SkyView Software v14.1, released 2016-03-29. Fixed:
o The issue described in the SkyView Software 14.0 Technical Service Bulletin
where certain SkyView displays running version 14.0 would become
unresponsive.
o Systems with SV-ARINC-429 would restart in certain situations.
o Spontaneous AP disconnects.
o Spurious "caution" alerts.
o Momentary Red-X on displays.
o Momentary SV-COM-PANEL offline alerts.
o System restarts caused by corner case (uncommon) software conditions.
o Video input from external sources would freeze in certain situations.
o In some circumstances, Initial/recurrent backup battery test routine would
not start even when battery was actually charged due to incorrect voltage
thresholds.
Software changes in SkyView Software v14.1.1, released 2016-03-31. Fixed:
o An issue that could cause transponders to become inoperative – and
therefore requiring return to Dynon Avionics – during a software update.
New products included in this revision:
o Dual ADAHRS Mounting Kit (P/N 102532-000)
o Panel Module Faceplate Blank (P/N 102542-000)
o Pitot/Static/AOA Pneumatic Installation Kit (P/N 102628-000)
o SkyView SE (SV-D600 and SV-D900 displays)
o SV-BUTTON-LEVEL (P/N 102553-000)
o SV-KNOB-DIMMER (P/N 102801-000)
New features included in v14.1 and v14.1.1:
o Support for SkyView SE
o When importing checklists, if there is an error, the line number of the
checklist file is displayed.
Significant documentation added:
o 9-pin D9F and D9M Connectors are SkyView Network (not RS-232 Serial)
(Page 2-1)
o SkyView Network is a “Party Line” (Page 2-2)
o Optional Components for Easier Installation of your SV-ADAHRS-200/201
(Page 5-4 and 5-5)
o US SkyView Pilots – Stadium TFR Database (Page 6-9)
o Retrofit Legacy Oil Pressure Sensor with Kavlico Oil Pressure sensor (Page 7-
49)
To Next Page
Loading...
