EasyManua.ls Logo

Huawei Quidway S9300

Huawei Quidway S9300
567 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Take the display on PE1 for example.
<PE1> display mpls ldp session
LDP Session(s) in Public Network
------------------------------------------------------------------------------
Peer-ID Status LAM SsnRole SsnAge KA-Sent/Rcv
------------------------------------------------------------------------------
2.2.2.2:0 Operational DU Passive 000:00:03 16/16
3.3.3.3:0 Operational DU Passive 000:00:00 1/1
------------------------------------------------------------------------------
TOTAL: 2 session(s) Found.
LAM : Label Advertisement Mode SsnAge Unit : DDD:HH:MM
Step 7 Configure tunnel policies on PEs.
# Configure PE1.
[PE1] tunnel-policy p1
[PE1-tunnel-policy-p1] tunnel select-seq cr-lsp load-balance-number 1
[PE1-tunnel-policy-p1] quit
# Configure PE3.
[PE3] tunnel-policy p1
[PE3-tunnel-policy-p1] tunnel select-seq cr-lsp load-balance-number 1
[PE3-tunnel-policy-p1] quit
Step 8 Configure PWs on PEs by using PW templates.
# Configure a master PW and a backup PW on PE1. Configure a PW on each of PE2 and PE3.
The two PWs are both master PWs.
# Configure PE1.
[PE1] mpls l2vpn
[PE1-l2vpn] mpls l2vpn default martini
[PE1-l2vpn] quit
[PE1] pw-template 1to2
[PE1-pw-template-1to2] peer-address 2.2.2.2
[PE1-pw-template-1to2] control-word
[PE1-pw-template-1to2] vccv cc cw cv lsp-ping bfd
[PE1-pw-template-1to2] quit
[PE1] pw-template 1to3
[PE1-pw-template-1to3] peer-address 3.3.3.3
[PE1-pw-template-1to3] control-word
[PE1-pw-template-1to3] vccv cc cw cv lsp-ping bfd
[PE1-pw-template-1to3] quit
[PE1] interface vlanif 10
[PE1-Vlanif10] mpls l2vc pw-template 1to3 100 tunnel-policy p1
[PE1-Vlanif10] mpls l2vc pw-template 1to2 200 secondary
[PE1-Vlanif10] quit
# Configure PE2.
[PE2] mpls l2vpn
[PE2-l2vpn] mpls l2vpn default martini
[PE2-l2vpn] quit
[PE2] pw-template 2to1
[PE2-pw-template-2to1] peer-address 1.1.1.1
[PE2-pw-template-2to1] control-word
[PE2-pw-template-2to1] vccv cc cw cv lsp-ping bfd
[PE2-pw-template-2to1] quit
[PE2] interface vlanif 50
[PE2-Vlanif50] mpls l2vc pw-template 2to1 200
[PE2-Vlanif50] quit
# Configure PE3.
Quidway S9300 Terabit Routing Switch
Configuration Guide - VPN 4 VLL Configuration
Issue 03 (2009-08-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
4-93

Table of Contents

Other manuals for Huawei Quidway S9300

Related product manuals