EasyManua.ls Logo

Huawei Quidway S9300

Huawei Quidway S9300
567 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
After the configuration, run the display bgp l2vpn peer command on the PEs. You can see that
BGP L2VPN peers are in Established state.
Take the display on PE1 for example.
<PE1> display bgp l2vpn peer
BGP local router ID : 1.1.1.1
Local AS number : 100
Total number of peers : 2 Peers in established state : 2
Peer V AS MsgRcvd MsgSent OutQ Up/Down State PrefRcv
2.2.2.2 4 100 25 25 0 00:18:36 Established 0
3.3.3.3 4 100 26 29 0 00:23:27 Established 0
Step 7 Configure tunnel policies on PEs.
# Configure PE1.
[PE1] tunnel-policy p1
[PE1-tunnel-policy-p1] tunnel select-seq cr-lsp load-balance-number 1
# Configure PE3.
[PE3] tunnel-policy p1
[PE3-tunnel-policy-p1] tunnel select-seq cr-lsp load-balance-number 1
Step 8 Confiugre Kompella L2VPN connections on the PEs.
# Configure PE1.
[PE1] interface vlanif 10
[PE1-Vlanif10] ip address 10.1.1.2 30
[PE1-Vlanif10] quit
[PE1] mpls l2vpn
[PE1-l2vpn] quit
[PE1] mpls l2vpn vpn1 encapsulation vlan control-word
[PE1-mpls-l2vpn-vpn1] route-distinguisher 100:1
[PE1-mpls-l2vpn-vpn1] vpn-target 1:1 both
[PE1-mpls-l2vpn-vpn1] ce ce1 id 1
[PE1-mpls-l2vpn-ce-vpn1-ce1] connection ce-offset 2 interface Vlanif 10 tunnel-
policy p1
[PE1-mpls-l2vpn-ce-vpn1-ce1] connection ce-offset 3 interface Vlanif 10 secondary
# Configure PE3.
[PE3] interface vlanif 60
[PE3-Vlanif60] ip address 10.1.1.1 30
[PE3-Vlanif60] quit
[PE3] mpls l2vpn
[PE3-l2vpn] quit
[PE3] mpls l2vpn vpn1 encapsulation vlan control-word
[PE3-mpls-l2vpn-vpn1] route-distinguisher 100:2
[PE3-mpls-l2vpn-vpn1] vpn-target 1:1 both
[PE3-mpls-l2vpn-vpn1] ce ce2 id 2
[PE3-mpls-l2vpn-ce-vpn1-ce2] connection ce-offset 1 interface Vlanif 60 tunnel-
policy p1
# Configure PE2.
[PE2] interface vlanif 50
[PE2-Vlanif50] ip address 10.1.1.1 30
[PE2-Vlanif50] quit
[PE2] mpls l2vpn
[PE2-l2vpn] quit
[PE2] mpls l2vpn vpn1 encapsulation vlan control-word
[PE2-mpls-l2vpn-vpn1] route-distinguisher 100:3
[PE2-mpls-l2vpn-vpn1] vpn-target 1:1 both
4 VLL Configuration
Quidway S9300 Terabit Routing Switch
Configuration Guide - VPN
4-110 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Issue 03 (2009-08-20)

Table of Contents

Other manuals for Huawei Quidway S9300

Related product manuals