Huawei Quidway S9300

[CE1-ospf-1-area-0.0.0.0] network 10.1.1.0 0.0.0.3
[CE1-ospf-1-area-0.0.0.0] network 10.1.3.0 0.0.0.255
# Configure CE2.
[CE2] ospf 1
[CE2-ospf-1] area 0
[CE2-ospf-1-area-0.0.0.0] network 10.1.1.0 0.0.0.3
[CE2-ospf-1-area-0.0.0.0] network 10.1.2.0 0.0.0.3
Run the display ip routing-table command on CE2. You can see that on CE2, the outgoing
interface of the routes to 10.1.3.0/24 is VLANIF 60. That is, the traffic is transmitted through
the primary path.
Take the display on CE2 for example.
<CE2> display ip routing-table
Route Flags: R - relied, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 5 Routes : 5
Destination/Mask Proto Pre Cost Flags NextHop Interface
10.1.1.0/30 Direct 0 0 D 10.1.1.2 Vlanif60
10.1.1.2/32 Direct 0 0 D 127.0.0.1 InLoopBack0
10.1.3.1/32 OSPF 10 2 D 10.1.1.1 Vlanif60
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
CE2 can ping 10.1.3.1 successfully.
<CE2> ping 10.1.3.1
PING 10.1.3.1: 56 data bytes, press CTRL_C to break
Reply from 10.1.3.1: bytes=56 Sequence=1 ttl=255 time=90 ms
Reply from 10.1.3.1: bytes=56 Sequence=2 ttl=255 time=160 ms
Reply from 10.1.3.1: bytes=56 Sequence=3 ttl=255 time=130 ms
Reply from 10.1.3.1: bytes=56 Sequence=4 ttl=255 time=130 ms
Reply from 10.1.3.1: bytes=56 Sequence=5 ttl=255 time=160 ms
--- 10.1.3.1 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 90/134/160 ms
Step 10 Verify the configuration.
Run the display mpls l2vpn connection interface command, and you can see that the local VC
status and remote VC status of the master PW and the backup PW are both Up, the forwarding
state of the master PW is True, and the forwarding state of the backup PW is False.
<PE1> display mpls l2vpn connection interface vlanif 10
conn-type: remote
local vc state: up
remote vc state: up
local ce-id: 1
local ce name: ce1
remote ce-id: 2
intf(state,encap): Vlanif10(up,vlan)
peer id: 3.3.3.3
route-distinguisher: 100:2
local vc label: 25602
remote vc label: 25601
tunnel policy: p1
primary or secondary: primary
forward entry exist or not: true
forward entry active or not:true
manual fault set or not: not set
4 VLL Configuration
Quidway S9300 Terabit Routing Switch
Configuration Guide - VPN
4-112 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Issue 03 (2009-08-20)