Huawei Quidway S9300

[PE1-Tunnel1/0/1] tunnel-protocol mpls te
[PE1-Tunnel1/0/1] destination 2.2.2.2
[PE1-Tunnel1/0/1] mpls te tunnel-id 11
[PE1-Tunnel1/0/1] mpls te bandwidth 5000
[PE1-Tunnel1/0/1] mpls te commit
[PE1-Tunnel1/0/1] quit
# Configure PE2.
[PE2] interface tunnel 1/0/1
[PE2-Tunnel1/0/1] ip address unnumbered interface loopback1
[PE2-Tunnel1/0/1] tunnel-protocol mpls te
[PE2-Tunnel1/0/1] destination 1.1.1.1
[PE2-Tunnel1/0/1] mpls te tunnel-id 11
[PE2-Tunnel1/0/1] mpls te bandwidth 5000
[PE2-Tunnel1/0/1] mpls te commit
[PE2-Tunnel1/0/1] quit
# Configure an MPLS TE tunnel with a bandwidth of 10 Mbit/s and bind the tunnel with the
VPN.
# Configure PE1.
[PE1] interface tunnel 1/0/2
[PE1-Tunnel1/0/2] ip address unnumbered interface loopback1
[PE1-Tunnel1/0/2] tunnel-protocol mpls te
[PE1-Tunnel1/0/2] destination 2.2.2.2
[PE1-Tunnel1/0/2] mpls te tunnel-id 22
[PE1-Tunnel1/0/2] mpls te bandwidth 10000
[PE1-Tunnel1/0/2] mpls te reserved-for-binding
[PE1-Tunnel1/0/2] mpls te commit
[PE1-Tunnel1/0/2] quit
# Configure PE2.
[PE2] interface tunnel 1/0/2
[PE2-Tunnel1/0/2] ip address unnumbered interface loopback1
[PE2-Tunnel1/0/2] tunnel-protocol mpls te
[PE2-Tunnel1/0/2] destination 1.1.1.1
[PE2-Tunnel1/0/2] mpls te tunnel-id 22
[PE2-Tunnel1/0/2] mpls te bandwidth 10000
[PE2-Tunnel1/0/2] mpls te reserved-for-binding
[PE2-Tunnel1/0/2] mpls te commit
[PE2-Tunnel1/0/2] quit
# By running the display interface tunnel interface-number command on the PEs, you can see
that Tunnel1/0/1 and Tunnel1/0/2 are both Up. Take Tunnel1/0/2 on PE1 for example.
[PE1] display interface tunnel 1/0/2
Tunnel1/0/2 current state : UP
Line protocol current state : UP
Description : HUAWEI, Quidway Series, Tunnel1/0/2 Interface, Route Port
The Maximum Transmit Unit is 1500 bytes
Internet Address is unnumbered, using address of LoopBack1(1.1.1.1/32)
Encapsulation is TUNNEL, loopback not set
Tunnel destination 2.2.2.2
Tunnel protocol/transport MPLS/MPLS, ILM is available,
primary tunnel id is 0x1003d, secondary tunnel id is 0x0
5 minutes output rate 0 bits/sec, 0 packets/sec
22894187 packets output, 2958834536 bytes
0 packets output dropped
# By running the display tunnel-info all command on the PEs, you can see that Tunnel1/0/1
and Tunnel1/0/2 are both Up. Take the display on PE1 as an example:
[PE1] display tunnel-info all
* -> Allocated VC Token
Tunnel ID Type Destination Token
----------------------------------------------------------------------
1 VPN Tunnel Management
Quidway S9300 Terabit Routing Switch
Configuration Guide - VPN
1-30 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Issue 03 (2009-08-20)