EasyManua.ls Logo

Huawei Quidway S9300

Huawei Quidway S9300
567 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
[PE1-GigabitEthernet1/0/1] port hybrid pvid vlan 7
[PE1-GigabitEthernet1/0/1] port hybrid tagged vlan 7
[PE1-GigabitEthernet1/0/1] quit
[PE1] interface vlanif 7
[PE1-Vlanif7] ip address 100.1.1.2 24
[PE1-Vlanif7] quit
[PE1]isis 1
[PE1-isis-1] network-entity 10.0000.0000.0000.0001.00
[PE1-isis-1] is-level level-2
[PE1-isis-1] quit
[PE1] interface vlanif 7
[PE1-Vlanif7] isis enable 1
[PE1-Vlanif7] quit
[PE1] interface loopback 1
[PE1-LoopBack1] ip address 1.1.1.9 32
[PE1-LoopBack1] isis enable 1
[PE1-LoopBack1] quit
# The configuration procedures of PE2 and PE3 are similar to the configuration procedure of
PE1.
# Configure the P.
<Quidway> system-view
[Quidway] sysname P
[P] vlan batch 5 6 7
[P]interface GigabitEthernet 1/0/1
[P-GigabitEthernet1/0/1] port hybrid pvid vlan 7
[P-GigabitEthernet1/0/1] port hybrid tagged vlan 7
[P-GigabitEthernet1/0/1] quit
[P]interface GigabitEthernet 1/0/2
[P-GigabitEthernet1/0/2] port hybrid pvid vlan 5
[P-GigabitEthernet1/0/2] port hybrid tagged vlan 5
[P-GigabitEthernet1/0/2] quit
[P]interface GigabitEthernet 1/0/3
[P-GigabitEthernet1/0/3] port hybrid pvid vlan 6
[P-GigabitEthernet1/0/3] port hybrid tagged vlan 6
[P-GigabitEthernet1/0/3] quit
[P] interface vlanif 7
[P-Vlanif7] ip address 100.1.1.1 24
[P-Vlanif7] quit
[P] interface vlanif 5
[P-Vlanif5] ip address 100.2.1.1 24
[P-Vlanif5] quit
[P] interface vlanif 6
[P-Vlanif6] ip address 100.3.1.1 24
[P-Vlanif6] quit
[P]isis 1
[P-isis-1] network-entity 10.0000.0000.0000.0002.00
[P-isis-1] is-level level-2
[P-isis-1] quit
[P] interface vlanif 5
[P-Vlanif5] isis enable 1
[P-Vlanif5] quit
[P] interface vlanif 6
[P-Vlanif6] isis enable 1
[P-Vlanif6] quit
[P] interface vlanif 7
[P-Vlanif7] isis enable 1
[P-Vlanif7] quit
[P] interface loopback 1
[P-LoopBack1] ip address 1.1.1.9 32
[P-LoopBack1] isis enable 1
[P-LoopBack1] quit
# Run the display ip routing-table command in any view of the PEs, and you can see that the
PEs can learn the loopback address of each other.
# Take the display on PE1 as an example:
Quidway S9300 Terabit Routing Switch
Configuration Guide - VPN 1 VPN Tunnel Management
Issue 03 (2009-08-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1-41

Table of Contents

Other manuals for Huawei Quidway S9300

Related product manuals