Huawei Quidway S9300

Session State : up
AC Status : up
VC State : up
VC ID : 200
VC Type : VLAN
Destination : 3.3.3.9
local VC Label : 17409 remote VC Label : 17408
Control Word : Disable
local VC MTU : 1500 remote VC MTU : 1500
Tunnel Policy Name : policy2
Traffic Behavior Name: --
PW Template Name : --
Create time : 0 days, 0 hours, 2 minutes, 23 seconds
UP time : 0 days, 0 hours, 0 minutes, 24 seconds
Last change time : 0 days, 0 hours, 0 minutes, 24 seconds
# Check information about the interfaces on the bound tunnel.
# Take Tunnel1/0/0 of PE1 as an example.
[PE1] display interface Tunnel 1/0/0
Tunnel1/0/0 current state : UP
Line protocol current state : UP
Description : HUAWEI, Quidway Series, Tunnel1/0/0 Interface, Route Port
The Maximum Transmit Unit is 1500
Internet Address is unnumbered, using address of LoopBack1(1.1.1.9/32)
Encapsulation is TUNNEL, loopback not set
Tunnel destination 2.2.2.9
Tunnel protocol/transport MPLS/MPLS, ILM is available,
primary tunnel id is 0x1003d, secondary tunnel id is 0x0
The tunnelIfIndex is 0x40038
QoS max-bandwidth : 64 Kbps
Output queue : (Urgent queue : Size/Length/Discards) 0/50/0
Output queue : (Protocol queue : Size/Length/Discards) 0/1000/0
Output queue : (FIFO queuing : Size/Length/Discards) 0/75/0
300 Seconds output rate 0 bits/sec, 0 packets/sec
0 packets output, 0 bytes
0 packets output dropped
# CE1 can ping CE2 and CE3.
# Display information about Tunnel1/0/0 on PE1.
[PE1] display interface Tunnel 1/0/0
Tunnel1/0/0 current state : UP
Line protocol current state : UP
Description : HUAWEI, Quidway Series, Tunnel1/0/0 Interface, Route Port
The Maximum Transmit Unit is 1500
Internet Address is unnumbered, using address of LoopBack1(1.1.1.9/32)
Encapsulation is TUNNEL, loopback not set
Tunnel destination 2.2.2.9
Tunnel protocol/transport MPLS/MPLS, ILM is available,
primary tunnel id is 0x1003d, secondary tunnel id is 0x0
The tunnelIfIndex is 0x40038
QoS max-bandwidth : 64 Kbps
Output queue : (Urgent queue : Size/Length/Discards) 0/50/0
Output queue : (Protocol queue : Size/Length/Discards) 0/1000/0
Output queue : (FIFO queuing : Size/Length/Discards) 0/75/0
300 Seconds output rate 2952 bits/sec, 2 packets/sec
48739720 packets output, 361150 bytes
0 packets output dropped
# You can see that the number of datagrams passing through Tunnel1/0/0 increases.
# Run the ping 20.1.1.2 command on CE1 to check information about Tunnel 1/0/0 of PE1. You
can see that the statistics of packets on Tunnel 1/0/0 remain unchanged because Tunnel 1/0/0
on PE1 transmits only the data between PE1 and PE2.
----End
Quidway S9300 Terabit Routing Switch
Configuration Guide - VPN 1 VPN Tunnel Management
Issue 03 (2009-08-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1-47