Index
Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide 1759
string variables, 86
string variables, reading multiple query
results into, 87
string variables, reading query results into
multiple, 87
string, quoted ASCII, 224
subnet mask, 72
subsource, waveform source, 1421
subsystem commands, 3, 1615
subtract math function, 490, 1417
subtract math function as g(t) source, 1508
sweep mode, trigger, 1295, 1310
sweep speed set to fast to measure fall
time, 590
sweep speed set to fast to measure rise
time, 611
switch disable, 1265
switching level, current, 799
switching level, voltage, 802
switching loss per cycle, 648
switching loss power analysis, 797
sync break, LIN, 981
sync frame count (FlexRay), 931
syntax elements, 223
syntax rules, program data, 1614
syntax, optional terms, 223
syntax, program message, 1611
SYSTem commands, 1259
system commands, 1261, 1263, 1264,
1265, 1277, 1279
system commands introduction, 1260
T
table of current harmonics results, 737
tdelta, 1520
Tektronix probe model number, 357
telnet ports 5024 and 5025, 1403
Telnet sockets, 89
temporary message, 1263
TER (Trigger Event Register), 296, 1565
termination conditions, mask test, 684
test sigma, mask test run, 689
test, self, 253
test, USB 2.0 signal quality, 375
text, writing to display, 1263
THD (total harmonics distortion), 746
threshold, 399, 703, 1500, 1547
threshold for FFT peak search, 1169
threshold voltage (lower) for
measurement, 1518
threshold voltage (upper) for
measurement, 1527
thresholds, 578, 1521
thresholds used to measure period, 603
thresholds, how autoscale affects, 261
time base, 1283, 1284, 1285, 1289,
1546
time base commands introduction, 1282
time base reference, 1287
time base reset conditions, 245, 1267
time base window, 1291, 1292, 1293
time between arm and trigger, NFC arm and
trigger event, 1341
time between points, 1520
time buckets, 303, 304
time delay, 1546
time delay, Edge Then Edge trigger, 1314
time delta, 1520
time difference between data points, 1425
time duration, 1337, 1356, 1357,
1359
time holdoff for trigger, 1301
time interval, 626, 1520
time interval between trigger and
occurrence, 1526
time marker sets start time, 1521
time measurements with X cursors, 539
time per division, 1285
time record, 483
time reference, lister, 526
time specified, 640, 1531
time, calibration, 341
time, mask test run, 690
time, runt pulse search, 1174
time, runt trigger, 1364
time, start marker, 1524
time, stop marker, 1525
time, system, 1279
time, transition search, 1179
time, transition trigger, 1375
time/div, how autoscale affects, 261
time-at-max measurement, 1522
time-at-min measurement, 1523
TIMebase commands, 1281
timebase vernier, 1290
TIMebase:MODE, 84
time-ordered label list, 419
timeout enable, NFC arm and trigger
event, 1348
timeout occurred, NFC arm and trigger
event, 1347
timeout period, NFC arm and trigger
event, 1349
timeout, SPI clock, 1077
timing measurement, 568
title channels, 352
title, mask test, 698
token PID, USB search, 1255
token PID, USB trigger, 1133
tolerance for determining valid SENT sync
pulses, 1063
tolerance, automask, 674, 675
top of waveform value measured, 636
total frame count (CAN), 884
total frame count (FlexRay), 932
Total Harmonic Distortion, FFT analysis
measurement, 594
total harmonics distortion (THD), 746
total waveforms in mask test, 679
touchscreen on/off,
1280
trace memory, 294
track measurements, 613
tracking, dual channel waveform
generator, 1472
transfer instrument state, 239, 1277
transforms, math, 490
transient response, 663
transient response analysis, 803, 804, 807
TRANsition SEARch commands, 1175
transition search qualifier, 1176
transition search slope, 1177
transition search time, 1179
transition trigger qualifier, 1372
transition trigger slope, 1373
transition trigger source, 1178, 1374
transition trigger time, 1375
transmit word size, I2S, 960
transparent screen background, remote
command logging, 1275
transparent, display, 424
tree traversal rules, 1615
trend measurement, 501
TRG (Trigger), 249, 251, 252
TRIG OUT BNC, 335
trigger armed event register, 280, 283
trigger armed status, checking for, 1581
trigger burst, UART, 1106
trigger channel source, 1338, 1380
TRIGger commands, 1295
TRIGger commands, general, 1297
trigger data, UART, 1107
TRIGger DELay commands, 1311
trigger duration, 1356, 1357
TRIGger EBURst commands, 1318
TRIGger EDGE commands, 1323
trigger edge coupling, 1325
trigger edge slope, 1328
trigger edge slope, Edge Then Edge
trigger, 1316
trigger edge source, Edge Then Edge
trigger, 1317
trigger event bit, 296
Trigger Event Register (TER), 1565
trigger event, NFC trigger, 1345
TRIGger FLEXray commands, 924
TRIGger GLITch commands, 1330
trigger holdoff, 1301
trigger idle, UART, 1108
TRIGger IIC commands, 962
trigger level auto set up, 1305
trigger level constants, 354
trigger level voltage, 1326
trigger level, high, 1306
trigger level, low, 1307
TRIGger LIN commands, 973
TRIGger M1553 commands, 992
TRIGger NFC commands, 1339
trigger occurred, 251
TRIGger OR commands, 1350
TRIGger PATTern commands, 1352
trigger pattern qualifier, 1358
trigger qualifier, UART, 1109
trigger reset conditions, 245, 1267
TRIGger RUNT commands, 1360
To Next Page
Loading...
Need help?
General
