Olympus 38DL PLUS User Manual

DMTA-10004-01EN, Rev. D, November 2016
List of Figures 292
Figure 11-17 Copying a file ................................................................................................... 186
Figure 11-18 Entering new file information ........................................................................ 187
Figure 11-19 Displaying the grid edit screen ...................................................................... 188
Figure 11-20 Deleting a file .................................................................................................... 189
Figure 11-21 Deleting the data of an ID range in the active file ....................................... 190
Figure 11-22 Warning message when resetting measurements ....................................... 191
Figure 11-23 The FILE NOTES screen ................................................................................. 192
Figure 11-24 Selecting a note from the notes table ............................................................ 194
Figure 11-25 Copying a note table from one file to another ............................................. 196
Figure 11-26 The ID overwrite protection message ........................................................... 197
Figure 11-27 Identifying the ID review screen ................................................................... 198
Figure 11-28 Editing the ID # edit mode ............................................................................. 200
Figure 11-29 The message when the edited ID is not in the database ............................ 201
Figure 11-30 The FILE SUMMARY report screen .............................................................. 203
Figure 11-31 The FILE SUMMARY report result screen ................................................... 204
Figure 11-32 The MIN/MAX SUMMARY report screen ................................................... 204
Figure 11-33 The FILE COMPARISON report screen ....................................................... 205
Figure 11-34 The FILE COMPARISON report result screen ............................................ 206
Figure 11-35 The ALARM SUMMARY report result screen ............................................ 207
Figure 11-36 The MIN/MAX SUMMARY report result screen ........................................ 208
Figure 11-37 Returning to the measurement screen .......................................................... 208
Figure 12-1 The GENERIC SETUP SELECTION screen ................................................. 213
Figure 12-2 Example of the ACTIVE screen ..................................................................... 214
Figure 12-3 Illustration of the V-path ................................................................................. 216
Figure 12-4 Answering YES at the V-path calibration prompt ...................................... 218
Figure 12-5 Editing point 1 of the V-path calibration ...................................................... 219
Figure 12-6 Saving the setup ............................................................................................... 220
Figure 13-1 The ACTIVE screen for the setup of a single element transducer ............ 222
Figure 13-2 Adjusting the waveform parameters ............................................................ 224
Figure 13-3 Mode 1 detection example .............................................................................. 226
Figure 13-4 Mode 2 detection example .............................................................................. 226
Figure 13-5 Mode 3 detection example .............................................................................. 227
Figure 13-6 Detection of the first or the second negative peak ...................................... 228
Figure 13-7 Comparing pulser power set to 60 V and 200 V .......................................... 229
Figure 13-8 The TDG zones and parameters .................................................................... 230
Figure 13-9 Main bang blank position for mode 1 ........................................................... 232
Figure 13-10 Main bang blank position for mode 2 and mode 3 ..................................... 233
Figure 13-11 Echo window setting for mode 1 ................................................................... 234
Figure 13-12 Echo window setting for mode 2 and mode 3 ............................................. 234
Figure 13-13 Negative and positive echo detection examples ......................................... 235
Figure 13-14 Examples of the interface blank in mode 2 .................................................. 237
Figure 13-15 Examples of the interface blank in mode 3 .................................................. 238

Olympus 38DL PLUS Specifications

General

Operating Temperature	-10 °C to 50 °C (14 °F to 122 °F)
Data Logger	Yes
Interface	USB, RS-232
Thickness Range	0.08 mm to 635 mm (0.003 in. to 25 in.) depending on material and transducer
Display	Backlit LCD
Battery Type	Three alkaline or NiMH AA cells
Pulser	Adjustable square wave pulser
Receiver Bandwidth	0.5 MHz to 20 MHz
Languages	English, French, German, Spanish, Italian, Russian, Japanese, Chinese
Resolution	0.001 mm or 0.0001 in.
Transducer Frequency	2 MHz to 30 MHz
Material	Plastic housing