Omron RX2 Series - Page 27

25
CONTENTS
High-function General-purpose Inverter RX2 Series User’s Manual
5-14 Analog Input Value Monitor ................................................................................................ 5-24
5-15 Analog Terminal Setting Monitor ....................................................................................... 5-25
5-16 Terminal Block Type Monitor.............................................................................................. 5-26
5-17 Operation Command/Frequency Command Sources Monitor........................................ 5-27
5-18 Options Monitor................................................................................................................... 5-28
Section 6 Basic Parameter Settings
6-1 Basic Parameter Settings ..................................................................................................... 6-3
6-1-1 Inverter Load Rating Settings ..................................................................................................... 6-3
6-1-2 Inverter Initialization.................................................................................................................... 6-5
6-2 Parameter Setting for Motor Related ................................................................................... 6-8
6-2-1 Motor Basic Settings................................................................................................................... 6-8
6-2-2 Motor Constant Setting............................................................................................................. 6-12
6-2-3 Auto-tuning of Motor ................................................................................................................. 6-14
6-3 Operation Command Settings............................................................................................ 6-19
6-3-1 Types of Operation Commands................................................................................................ 6-19
6-3-2 Operation with LCD Operator ................................................................................................... 6-19
6-3-3 Operation with Forward/Reverse Rotation Terminal ................................................................. 6-20
6-3-4 Operation with 3 Wire Function of Terminal Block.................................................................... 6-21
6-3-5 Operation with RS485 Communication..................................................................................... 6-22
6-3-6 Operation from Optional Unit.................................................................................................... 6-22
6-3-7 Disabling the Keys on LCD Operator........................................................................................6-23
6-3-8 Temporary Change of Operation Command Destination.......................................................... 6-24
6-4 Frequency Command Settings........................................................................................... 6-25
6-4-1 Frequency Command Selection ...............................................................................................6-25
6-4-2 Case where Command Is Given with LCD Operator................................................................ 6-26
6-4-3 Case where Command Is Given from Terminal Block Analog Signals ..................................... 6-27
6-4-4 Case where Command Is Given through RS485 Communications.......................................... 6-28
6-4-5 Case where Command Is Given through Input of Pulse String ................................................ 6-28
6-4-6 Case where Command Is Given through DriveProgramming................................................... 6-34
6-4-7 Case where Command Is Given with PID Control.................................................................... 6-34
6-4-8 Case where Command Is Given with Main Speed Command and Auxiliary Speed
Command ................................................................................................................................. 6-35
6-4-9 Case where Command Is Given with Multi-Step Speed........................................................... 6-37
6-4-10 Temporal Addition of Frequency Command.............................................................................. 6-41
6-4-11 Up/Down Function (FUP, FDN)................................................................................................. 6-41
6-4-12 Analog Command Hold Function (AHD)................................................................................... 6-42
6-4-13 Temporal Change of Frequency Command Destinations......................................................... 6-43
6-5 Limit Frequency and Operation Commands..................................................................... 6-44
6-5-1 Limit Frequency and Operation Commands............................................................................. 6-44
6-5-2 Limit Operation Command Direction.........................................................................................6-45
6-5-3 Limit Output Direction ............................................................................................................... 6-45
6-5-4 Operation Permission ............................................................................................................... 6-46
6-6 Thermal Protection of Motor (Electronic Thermal)........................................................... 6-48
6-6-1 Electronic Thermal Setting........................................................................................................ 6-48
6-6-2 Monitoring of Motor Temperature.............................................................................................. 6-55
6-7 Acceleration/Deceleration Settings ................................................................................... 6-56
6-7-1 Change Acceleration Time and Deceleration Time................................................................... 6-56
6-7-2 Switch Acceleration Time and Deceleration Time in Two Stages ............................................. 6-58
6-7-3 Switching of Acceleration or Deceleration Time with Multi-Speed Step.................................... 6-61
6-7-4 Holding Function of Acceleration/Deceleration......................................................................... 6-66
6-7-5 Change the Acceleration or Deceleration Pattern..................................................................... 6-67
6-7-6 Following Frequency Command...............................................................................................6-70