EasyManua.ls Logo

Omron RX2 Series - Page 29

Omron RX2 Series
920 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
27
CONTENTS
High-function General-purpose Inverter RX2 Series User’s Manual
8-2-1 Overload Limit Level Function.................................................................................................. 8-40
8-2-2 Overcurrent Suppression Selection.......................................................................................... 8-42
8-2-3 Overvoltage Suppression Function During Deceleration.......................................................... 8-44
8-2-4 Overexcitation Function............................................................................................................ 8-47
8-2-5 Regenerative Braking Function ................................................................................................ 8-50
8-2-6 Restart during Power Interruption/Undervoltage ...................................................................... 8-52
8-2-7 Restart on Overvoltage/Overcurrent......................................................................................... 8-58
8-2-8 Non-stop on Momentary Power Interruption............................................................................. 8-63
8-3 Protective Functions ........................................................................................................... 8-69
8-3-1 Input Power Supply Phase Loss Protection.............................................................................. 8-69
8-3-2 Output Phase Loss Protection Function ................................................................................... 8-69
8-3-3 External Trip (EXT) Function .................................................................................................... 8-70
8-3-4 Power Recovery Restart Prevention Function (USP)............................................................... 8-71
8-3-5 Overcurrent Detection............................................................................................................... 8-71
8-3-6 Instantaneous Power Interruption/Undervoltage Detection ...................................................... 8-72
8-3-7 Frequency Jump Function........................................................................................................ 8-77
8-3-8 Speed Deviation Error Detection .............................................................................................. 8-78
8-3-9 Overspeed Error Detection....................................................................................................... 8-79
8-4 Control Function.................................................................................................................. 8-80
8-4-1 2nd Control (SET)..................................................................................................................... 8-80
8-4-2 Commercial Switch (CS)........................................................................................................... 8-81
8-4-3 Jogging Operation Function (JG).............................................................................................. 8-83
8-4-4 Brake Control Function (BRK) .................................................................................................. 8-85
8-4-5 Contactor Control (CON) .......................................................................................................... 8-91
8-4-6 Forced Operation...................................................................................................................... 8-94
8-4-7 Pulse Train Position Control ..................................................................................................... 8-99
8-4-8 Orientation Control.................................................................................................................. 8-105
8-4-9 Absolute Position Control ....................................................................................................... 8-108
8-4-10 Servo Lock (SON)................................................................................................................... 8-120
8-5 Cooling Fan Control .......................................................................................................... 8-122
8-6 Alarm Signal....................................................................................................................... 8-123
8-6-1 Alarm Signal (AL).................................................................................................................... 8-123
8-6-2 Fatal Fault Signal (MJA) ......................................................................................................... 8-125
8-6-3 Alarm Code............................................................................................................................. 8-126
8-6-4 Overload Warning Function (OL/OL2) .................................................................................... 8-127
8-6-5 Low Current Signal (LOC) ...................................................................................................... 8-129
8-6-6 Momentary Power Interruption Signal (IP).............................................................................. 8-131
8-6-7 Signal during Undervoltage (UV)............................................................................................ 8-132
8-6-8 Motor Thermal Warning Signal (THM).................................................................................... 8-133
8-6-9 Inverter Thermal Warning Signal (THC) ................................................................................. 8-134
8-6-10 Cooling Fin Overheat Warning Signal (OHF) ......................................................................... 8-135
8-6-11 Capacitor Life Warning Signal (WAC)..................................................................................... 8-136
8-6-12 Cooling Fan Life Warning Signal (WAF) ................................................................................. 8-136
8-6-13 RUN Time Over Signal (RNT)................................................................................................. 8-137
8-6-14 Power ON Time Over Signal................................................................................................... 8-138
8-6-15 Incoming Overvoltage Signal (OVS)....................................................................................... 8-139
8-7 Terminal Output During Run ............................................................................................ 8-140
8-7-1 Signal during RUN (RUN)....................................................................................................... 8-140
8-7-2 Signal during RUN (FWR/RVR).............................................................................................. 8-141
8-7-3 Starting Contact Signal........................................................................................................... 8-142
8-7-4 Operation Ready (IRDY)......................................................................................................... 8-143
8-8 Frequency Arrival Signal (FA1 to FA5) ............................................................................ 8-144
8-8-1 Output Signal on Constant Speed Arrival (FA1) ..................................................................... 8-144
8-8-2 Set Frequency Exceeded Signal (FA2/FA4) ........................................................................... 8-145
8-8-3 Set Frequency Matched Signal (FA3/FA5) ............................................................................. 8-146
8-8-4 0-Hz Detection Signal (ZS)..................................................................................................... 8-147
8-9 Applied Output................................................................................................................... 8-148
8-9-1 Analog Disconnection Signal.................................................................................................. 8-148
8-9-2 Logical Output Signal.............................................................................................................. 8-151
8-10 Input Terminal Function ....................................................................................................8-154

Table of Contents

Related product manuals