Parameters
Connector/Binector (BICO)-Parameters
1-310
© Siemens AG 2007 All Rights Reserved
SINAMICS G120 Control Units CU240S, Edition 05/2007
1.4.4 Connector Output Parameters
r0020 CO: Freq. setpoint before RFG / Setp before RFG
r0021 CO: Act. filtered frequency / Act. filt. freq.
r0024 CO: Act. filt. output frequency / Act. outp. freq
r0025 CO: Act. output voltage / Act.outp. volt
r0026[0...1] CO: Act. filtered DC-link volt. / Act. fil. Vdc
r0027 CO: Act. output current / Act. outp. cur
r0029 CO: Flux gen. current / Flux gen. cur.
r0030 CO: Torque gen. current / Torque gen.cur
r0031 CO: Act. filtered torque / Act fil torque
r0032 CO: Act. filtered power / Act fil. power
r0035[0...2] CO: Act. motor temperature / Act. mot.temp.
r0036 CO: Inverter overload utilization / Invert ovl util
r0037[0...1] CO: Inverter temperature [°C] / Inverter temp.
r0038 CO: Fil. power factor / Fil.power fact
r0039 CO: Energy consumpt. meter [kWh] / Energy meter
r0051[0...1] CO: Active Drive Dataset (DDS) / Active DDS
r0061 CO: Act. rotor speed / Act rotor speed
r0062 CO: Freq. setpoint / Freq. setpoint
r0063 CO: Act. frequency / Act. frequency
r0064 CO: Dev. frequency controller / Dev. freq ctrl
r0065 CO: Slip frequency / Slip frequency
r0066 CO: Act. output frequency / Act. outp freq
r0067 CO: Act. output current limit / Outp cur limit
r0068 CO: Output current / Output current
r0069[0...5] CO: Act. phase currents / Act. phase cur
r0070 CO: Act. DC-link voltage / Act. Vdc
r0071 CO: Max. output voltage / Max. outp.volt
r0072 CO: Act. output voltage / Act. outp.volt
r0074 CO: Act. modulation / Act modulation
r0075 CO: Current setpoint Isd / Cur. setp. Isd
r0076 CO: Act. current Isd / Act. cur. Isd
r0077 CO: Current setpoint Isq / Cur. setp. Isq
r0078 CO: Act. current Isq / Act. cur. Isq
r0079 CO: Torque setpoint (total) / Total trq setp
r0080 CO: Act. torque / Act. torque
r0084 CO: Act. air gap flux / Air gap flux
r0085 CO: Act. re-active current / Act.re-active cur
r0086 CO: Act. active current / Act.active cur
r0087 CO: Act. power factor / Act.power fact
r0090 CO: Act. rotor angle / Act rotor angle
r0094 CO: Transformation angle / Transf. angle
r0394 CO: Stator resistance IGBT [%] / Stat. res.IGBT
r0395 CO: Total stator resistance [%] / Total stat.res
r0396 CO: Act. rotor resistance / Act rotor res.
r0485 CO: Encoder counter value / Encoder count val.
r0623[0...2] CO: Display for the identified stator resistance / Act. stator resist
r0630[0...2] CO: Motor model ambient temperature / Mot. model amb. te
r0631[0...2] CO: Stator iron temperature / Stat.iron temp
r0632[0...2] CO: Stator winding temperature / Stat.wind.temp
r0633[0...2] CO: Rotor winding temperature / Rot. wind.temp
r0755[0...1] CO: Act. AI after scal. [4000h] / CO:AI scal[4000h]
r0947[0...63] CO: Last fault code / Last fault code
r0949[0...63] CO: Fault value / Fault value
To Next Page
Loading...
Need help?
General
