EasyManuals Logo

Cisco Nexus 7000 Series Reference Guide

Cisco Nexus 7000 Series
746 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #184 background imageLoading...
Page #184 background image
E Commands
event module-failure
156
Cisco Nexus 7000 Series NX-OS System Management Command Reference
OL-25806-03
event module-failure
To specify an event criteria for an Embedded Event Manager (EEM) applet that is run on the basis of a
module failure event, use the event module-failure command. To remove the module failure event
criteria, use the no form of this command.
event module-failure type err-name module {all | module} count count [time interval]
no event module-failure type err-name module {all | module} count count
Syntax Description type err-name Specifies the type of failure condition. Select one of the err-name conditions:
any—Any failure
addon-sequence-failure—Addon sequence failure
hitless-upgrade-diag-failure—Runtime diagnostic failure after hitless upgrade
hitless-upgrade-failure—Hitless upgrade failure
hitless-upgrade-procmgr-notif—LC software failure after hitless upgrade
hitless-upgrade-reg-failure—Registration failure after hitless upgrade
hitless-upgrade-seq-timeout—Hitless upgrade sequence timeout
image-download-failed—Image download failure
image-upgrade-failed—Image upgrade failed
insertion-seq-failure—Insertion sequence failure
lc-failed—LC failed
lc-not-responding—LC not responding
lc-ready-timeout—LC ready timeout
lc-sw-failure—LC software failure
registration-failure—Registration failure
registration-timeout—Registration timeout
runtime-diag-failure—Runtime diag failure
runtime-diag-timeout—Runtime diag timeout
sequence-timeout—Sequence timeout
srg-info-resp-timeout—SRG info response timeout
unexpected-registration—Unexpected registration received
upgrade-srg-not-compatible—Upgrade SRG not compatible
module Specifies that one module or all modules must be monitored.
module Number of a specific module to be monitored.
all Specifies that all modules are to be monitored.
count count Specifies the number of matching occurrences before a module failure event is
triggered. The range is from 0 to 4294967295.
time interval (Optional) Specifies the time interval (in seconds) within which the events need
to happen. The range is from 0 to 4294967295.

Table of Contents

Other manuals for Cisco Nexus 7000 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Nexus 7000 Series and is the answer not in the manual?

Cisco Nexus 7000 Series Specifications

General IconGeneral
ChassisModular
Operating SystemCisco NX-OS
LatencySub-microsecond
IPv6 SupportYes
RedundancyPower supplies, fans, supervisors, fabric modules
Power SupplyAC or DC
Layer SupportL2, L3
Network ManagementCLI, SNMP
VirtualizationVRF, vPC
Ports10 Gigabit Ethernet, 40 Gigabit Ethernet, 100 Gigabit Ethernet, Fibre Channel, Fibre Channel over Ethernet (FCoE)
Supported ModulesVarious (1G, 10G, 40G, 100G)
FeaturesFCoE, OTV, LISP
MPLS SupportYes
Quality of Service (QoS)Yes
Security FeaturesACLs, Cisco TrustSec, Control Plane Policing (CoPP)
DimensionsVaries by model
WeightVaries by model
Operating Temperature0 to 40°C (32 to 104°F)
Storage Temperature-40°F to 158°F (-40°C to 70°C)
Humidity5 to 95% noncondensing
MTBFVaries by model
Number of SlotsVaries by model (9-slot, 10-slot, 18-slot)

Related product manuals