EasyManua.ls Logo

Endress+Hauser Proline Promag 300 - Page 251

Endress+Hauser Proline Promag 300
272 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Proline Promag 300 Modbus RS485 Modbus RS485 Register Information
Endress+Hauser 251
Navigation: Expert → Output → PFS output 1 to n
Parameter Register Data type Access Selection / User entry / User interface → 
Switch status 1 to n (0461–1 to n) 1: 2485
2: 2486
3: 9917
Integer Read 1 = Open
6 = Closed
137
Invert outp.sig. (0470–1 to n) 1: 2583
2: 2584
3: 9916
Integer Read / Write 0 = Yes
1 = No
138
* Visibility depends on order options or device settings
"Relay output 1 to n" submenu
Navigation: Expert → Output → Relay output 1 to n
Parameter Register Data type Access Selection / User entry / User interface → 
Terminal no. (0812–1 to n) 1: 8278
2: 8279
3: 8280
Integer Read 0 = Not used
2 = 24-25 (I/O 2)
3 = 22-23 (I/O 3)
139
Relay outp.func. (0804–1 to n) 1: 2488
2: 2489
3: 9876
Integer Read / Write 1 = Open
2 = Diag. behavior
3 = Fl. direct.check
4 = Limit
5 = Digital Output
6 = Closed
139
Assign dir.check (0808–1 to n) 1: 8251
2: 8252
3: 8253
Integer Read / Write 0 = Off
1 = Volume flow
2 = Mass flow
3 = Correct.vol.flow
140
Assign limit (0807–1 to n) 1: 8248
2: 8249
3: 8250
Integer Read / Write 0 = Off
1 = Volume flow
2 = Mass flow
3 = Correct.vol.flow
4 = Conductivity
*
7 = Temperature
*
9 = CorrConductivity
*
16 = Totalizer 1
17 = Totalizer 2
18 = Totalizer 3
37 = Flow velocity
39 = Electronic temp.
140
Assign diag. beh (0806–1 to n) 1: 8245
2: 8246
3: 8247
Integer Read / Write 0 = Alarm
1 = Warning
2 = Alarm or warning
141
Assign status (0805–1 to n) 1: 8272
2: 8273
3: 8274
Integer Read / Write 0 = Low flow cut off
1 = Partial pipe det
141
Switch-off value (0809–1 to n) 1: 8260 to 8261
2: 8262 to 8263
3: 8264 to 8265
Float Read / Write Signed floating-point number 142
Switch-off delay (0813–1 to n) 1: 8254 to 8255
2: 8256 to 8257
3: 8258 to 8259
Float Read / Write 0.0 to 100.0 s 142
Switch-on value (0810–1 to n) 1: 8233 to 8234
2: 8235 to 8236
3: 8237 to 8238
Float Read / Write Signed floating-point number 142
Switch-on delay (0814–1 to n) 1: 8266 to 8267
2: 8268 to 8269
3: 8270 to 8271
Float Read / Write 0.0 to 100.0 s 143

Table of Contents

Other manuals for Endress+Hauser Proline Promag 300

Related product manuals