Appendices C Table of Parameters
C - 66
High-function General-purpose Inverter RX2 Series User’s Manual
Parameter Mode (Code U)
Code
Codes that
can be
changed
during
operation
Name Data range
Initial
value
Note
UA-01 -
Password input for display
selection
- 0000
UA-02 - Soft-lock password input - 0000
UA-10 - Display restriction selection
00 (Full display)/01 (By function)/02 (User setting)/
03 (Conveyor display)/04 (Only monitor display)
00
UA-12 ○
Accumulation input power moni-
tor clear
00 (Disabled)/01 (Clear) 00
UA-13 ○
Display gain for Accumulation
input power monitor
1 to 1000 1
UA-14 ○
Accumulation output power
monitor clear
00 (Disabled)/01 (Clear) 00
UA-15 ○
Display gain for Accumulation
output power monitor
1 to 1000 1
UA-16 ○ Soft-lock selection 00 ([SFT] terminal)/01 (Always enabled)00
UA-17 ○ Soft-lock target selection
00 (All data cannot be changed)/
01 (Data other than set frequency cannot be changed)
00
UA-18 - Data R/W selection 00 (R/W enabled)/01 (R/W disabled) 00
UA-19 - Low battery warning enable 00 (Disabled)/01 (Warning)/02 (Error) 00
UA-20 -
Action selection at Keypad dis-
connection
00 (Error)/01 (Error after deceleration stop)/02 (Ignore)/
03 (Free run)/04 (Deceleration stop)
02
UA-21 -
2nd-motor parameter display
selection
00 (Not display/01 (Display) 01
UA-22 -
Option parameter display selec-
tion
00 (Not display/01 (Display) 01
UA-30 -
User parameter auto setting
function enable
00 (Disabled)/01 (Enabled) 00
UA-31 ○ User parameter 1 selection no/***** (select a parameter) no
UA-32 ○ User parameter 2 selection no/***** (select a parameter) no
UA-33 ○ User parameter 3 selection no/***** (select a parameter) no
UA-34 ○ User parameter 4 selection no/***** (select a parameter) no
UA-35 ○ User parameter 5 selection no/***** (select a parameter) no
UA-36 ○ User parameter 6 selection no/***** (select a parameter) no
UA-37 ○ User parameter 7 selection no/***** (select a parameter) no
UA-38 ○ User parameter 8 selection no/***** (select a parameter) no
UA-39 ○ User parameter 9 selection no/***** (select a parameter) no
UA-40 ○ User parameter 10 selection no/***** (select a parameter) no
UA-41 ○ User parameter 11 selection no/***** (select a parameter) no
UA-42 ○ User parameter 12 selection no/***** (select a parameter) no
UA-43 ○ User parameter 13 selection no/***** (select a parameter) no
UA-44 ○ User parameter 14 selection no/***** (select a parameter) no
UA-45 ○ User parameter 15 selection no/***** (select a parameter) no
UA-46 ○ User parameter 16 selection no/***** (select a parameter) no
UA-47 ○ User parameter 17 selection no/***** (select a parameter) no
UA-48 ○ User parameter 18 selection no/***** (select a parameter) no
UA-49 ○ User parameter 19 selection no/***** (select a parameter) no
UA-50 ○ User parameter 20 selection no/***** (select a parameter) no
UA-51 ○ User parameter 21 selection no/***** (select a parameter) no
UA-52 ○ User parameter 22 selection no/***** (select a parameter) no
UA-53 ○ User parameter 23 selection no/***** (select a parameter) no
UA-5
4
○ User parameter 24 selection no/***** (select a parameter) no
UA-55 ○ User parameter 25 selection no/***** (select a parameter) no
UA-56 ○ User parameter 26 selection no/***** (select a parameter) no
UA-57 ○ User parameter 27 selection no/***** (select a parameter) no