Plockmatic BM3050 system 27 August 2019 3. Repairs and adjustments (REP and ADJ)
3-2
REP 7.7 BM-M23 Thick Sensor Motor
BM-Q37 Thick Set Motor Sensor &
BM-Q36 Thick Set Motor Home Sensor ..................................................3-61
REP 7.8 Removing Power Supply unit
..................................................................3-62
REP 7.9 Accessing Rear Side of Connection Bracket
.........................................3-63
REP 7.10 BM-M19 Infeed module motor M19 &
BM-Q34 Infeed motor sensor
...................................................................3-63
Belt Stacker REP’s
REP 8.0 Stacker Module .........................................................................................3-64
REP 8.1 ST-M1 Stacker Motor
................................................................................3-65
Trimmer REPs
REP 10.0 Front and Rear Cover .............................................................................3-66
REP 10.1 Top Cover
................................................................................................3-67
REP 10.2 Infeed Cover
............................................................................................3-68
REP 10.3 TR-M5 / M6 Blower Motor (Blower Assembly)
.....................................3-69
REP 10.4 Upper Exit Cover
....................................................................................3-69
REP 10.5 TR-SW10 Interlock Switch & TR-Q1 Interlock sensor
.........................3-70
REP 10.6 Protection Cover
.....................................................................................3-71
REP 10.7 TR-Q8 Trim Bin Full Sensor
...................................................................3-72
REP 10.8 TR-Q13 Infeed Sensor
............................................................................3-72
REP 10.9 TR-Q2 Infeed Shaft Sensor
....................................................................3-73
REP 10.10 TR-Q3 Exit Belt Sensor
.......................................................................3-73
REP 10.11 TR-M1 Transport / Knife Motor
..........................................................3-74
REP 10.12 TR-Q4 Transport Belt Sensor
.............................................................3-74
REP 10.13 TR-M2 Trim Knife Motor
.......................................................................3-75
REP 10.14 TR-Q5 Trim Knife Home Position Sensor
...........................................3-76
REP 10.15 Knife guard
...........................................................................................3-77
REP 10.16 Upper Trim Knife
...................................................................................3-78
REP 10.17 Lower Trim Knife
..................................................................................3-79
REP 10.18 TR-Q14 Paper Path & TR-Q6 Exit Sensor
..........................................3-81
REP 10.19 Stop Gate Carriage
...............................................................................3-82
REP 10.20 TR-M3 Stop Gate Motor,
TR-Q7 Stop Gate Home Position sensor &
TR-Q11 length adjustment home position sensor
.................................3-83
REP 10.21 TR-M4 Length Adjustment Motor &
TR-Q12 (M4) Motor Encoder
....................................................................3-84
REP 10.22 Lower Exit Belts and foam rollers
.......................................................3-85
REP 10.23 Upper Exit Belts and foam rollers
.......................................................3-87
REP 10.24 Transmission Chain
.............................................................................3-89
REP 10.25 Knife Support Chain
.............................................................................3-89
REP 10.26 Knife Chain
............................................................................................3-90
REP 10.27 Infeed Belts
...........................................................................................3-91
REP 10.28 MD6DC PCB ”A”
...................................................................................3-93
REP 10.29 Latch, Docking
......................................................................................3-94
REP 10.30 TR-M8 Lifter Motor &
TR-Q15 Lift Motor Home Pos. Sensor
.....................................................3-94
REP 10.31 Plunger, upper knife beam
...................................................................3-95
Square Folder REPs
REP 11.0 Front and Rear Cover .............................................................................3-96
REP 11.1 Infeed Cover
............................................................................................3-96
REP 11.2 Exit Cover Assembly
..............................................................................3-97
REP 11.3 Top Cover
................................................................................................3-98
REP 11.4 Tilt the Machine
.......................................................................................3-99
REP 11.5 Antistatic Brushes
................................................................................3-101
REP 11.6 SQF-M1 Transport Belt Motor
..............................................................3-101
REP 11.7 SQF-M2 Stop Gate Motor
.....................................................................3-102
REP 11.8 SQF-M3 Clamp Motor
...........................................................................3-103
REP 11.9 SQF-M4 Roll Motor
...............................................................................3-104
REP 11.10 SQF-Q1 (M2) Stop Gate Sensor
.........................................................3-106
REP 11.11 SQF-M4 Roll Motor,
SQF-Q2 (M4) Right sensor & SQF-Q3 (M4) Left Sensor
......................3-107
REP 11.12 SQF-Q4 Clamp Motor (M3) Encoder
..................................................3-107
REP 11.13 SQF-Q5 Infeed Sensors
......................................................................3-108
REP 11.14 SQF-Q7 Exit Sensors
..........................................................................3-108
To Next Page
