Plockmatic BM500 - Page 86

Plockmatic BM3050 system 27 August 2019 3. Repairs and adjustments (REP and ADJ)
3-3
REP 11.15 SQF-Q6 Clamp Sensor .......................................................................3-109
REP 11.16 SQF-M4 Roll Motor & SQF-Q8 (M4) Motor Sensor
...........................3-109
REP 11.17 Upper Transport Belt Assembly
........................................................3-110
REP 11.18 SQF-SW2 Interlock Switches
.............................................................3-111
REP 11.19 Upper Transport Belt, SQF-SOL1/3 Clutches & Foam Rollers
.......3-111
REP 11.20 Lower Transport Belt, SQF-SOL2/4 Clutches & Foam rollers
........3-113
REP 11.21 Teon Tape Lower Transport Belt
.....................................................3-115
REP 11.22 Set Clamps
..........................................................................................3-116
REP 11.23 Stop Gate
............................................................................................. 3-118
REP 11.24 MD6DC PCB ”D”
.................................................................................3-119
REP 11.25 Accessing Rear Side of Connection Bracket
...................................3-120
CST REPs
REP 12.0 Front and Rear Cover ..........................................................................3-121
REP 12.1 Infeed and Exit Cover
..........................................................................3-122
REP 12.2 Top Cover
..............................................................................................3-123
REP 12.3 Top Cover Assembly
............................................................................3-124
REP 12.4 Interlock Switch Assy Top Cover CT-SW3 (CT-Q9)
& Main power switch CT-SW1
................................................................3-126
REP 12.5 Interlock Switch Slide Door CT-SW2 (CT-Q8)
....................................3-127
REP 12.6 Entrance Sensor (CT-Q1)
.....................................................................3-127
REP 12.7 Exit Sensor (CT-Q7)
..............................................................................3-128
REP 12.8 Drive Motor (CT-M1)
.............................................................................3-129
REP 12.9 Drive Motor (CT-M1) Primary Timing Belt...........................................3-130
REP 12.10 Drive Motor (M1) Secondary Timing Belt
.........................................3-131
REP 12.11 Infeed Drive Shaft
...............................................................................3-132
REP 12.12 Infeed Idler Roller
...............................................................................3-132
REP 12.13 Infeed Bafe
........................................................................................3-133
REP 12.14 Exit Drive Shaft
...................................................................................3-133
REP 12.15 Exit Idler Roller
...................................................................................3-134
REP 12.16 Exit Bafe
............................................................................................3-135
REP 12.17 Pre Trimmer Fixing Roller
..................................................................3-136
REP 12.18 Post Trimmer Fixing Roller
................................................................3-137
REP 12.19 Transmission Shaft
............................................................................3-138
REP 12.20 Lower Drive Shaft
...............................................................................3-139
REP 12.21 Chassis Counter
.................................................................................3-140
REP 12.22 Waste Transport Belt
..........................................................................3-141
REP 12.23 Waste Bin Full Sensor (CT-Q11)
........................................................3-142
REP 12.24 Waste Transport Sensor (CT-Q14)
....................................................3-143
REP 12.25 Upper Drive Shaft
...............................................................................3-144
REP 12.26 Rotator Sensor (CT-Q2)
......................................................................3-145
REP 12.27 Rotator Timing Belt
............................................................................3-145
REP 12.28 Rotator Disengage Solenoid (CT-SOL1)
...........................................3-146
REP 12.29 Rotator Disengage Solenoid (CT-SOL1) Idler Shaft
........................3-147
REP 12.30 Rotator Disengage Solenoid (CT-SOL1) Mechanism
......................3-147
REP 12.31 Rotator Disengage Solenoid (CT-SOL2)
...........................................3-148
REP 12.32 Rotator Disengage Solenoid (CT-SOL2) Idler Shaft
........................3-149
REP 12.33 Rotator Disengage Solenoid (CT-SOL2) Mechanism
......................3-149
REP 12.34 Rotator Upper Drive Shaft
.................................................................3-150
REP 12.35 Rotator Lower Drive Shaft
.................................................................3-150
REP 12.36 Rotator Motor (CT-M3)
........................................................................3-151
REP 12.37 Rotator Motor (CT-M3) Drive Shaft
....................................................3-152
REP 12.38 Registration Lead Screw
....................................................................3-152
REP 12.39 Registration Width Adjustment Motor (CT-M4)
................................3-153
REP 12.40 Registration M4 Home Sensor (CT-Q3)
............................................3-154
REP 12.41 Registration Cross Rolls Drive Shaft
................................................3-155
REP 12.42 Registration Cross Rollers Timing Belt
............................................3-156
REP 12.43 Registration Cross Rollers
..............................................................3-157
REP 12.44 Registration Cross Rollers Idler Rollers
..........................................3-158
REP 12.45 Registration Primary Alignment Rail
................................................3-159
REP 12.46 Registration Secondary Alignment Rail
...........................................3-159
REP 12.47 Registration Disengage Solenoid (CT-SOL5)
...................................3-160
REP 12.48 Registration Disengage Solenoid (SOL5) Linkage
..........................3-161
REP 12.49 Creaser Assembly
..............................................................................3-162
REP 12.50 Creaser Trigger Sensor (CT-Q4) LED
................................................3-164