Parameters
Command and Drive Data Sets – Overview
1-304
© Siemens AG 2007 All Rights Reserved
SINAMICS G120 Control Units CU240S, Edition 05/2007
p1520[0...2] CO: Upper torque limit / Upper trq. lim
p1521[0...2] CO: Lower torque limit / Lower trq. lim
p1525[0...2] Scaling lower torque limit / Scal. low trq. lim
p1530[0...2] Motoring power limitation / Motoring power lim
p1531[0...2] Regenerative power limitation / Regener. power lim
p1570[0...2] CO: Fixed value flux setpoint / Fval flux setp
p1574[0...2] Dynamic voltage headroom / Dyn. volt headroom
p1580[0...2] Efficiency optimization / Efficiency optimiz
p1582[0...2] Smooth time for flux setpoint / Flux setp. Tsmooth
p1596[0...2] Int. time field weak. controller / Int.time weak.ctrl
p1610[0...2] Continuous torque boost (SLVC) / Cont. torque boost
p1611[0...2] Acc. torque boost (SLVC) / Acc trq boost SLVC
p1654[0...2] Smooth time for Isq setpoint / Isq setp. Tsmooth
p1715[0...2] Gain current controller / Gain current ctrl.
p1717[0...2] Integral time current controller / Int.time cur. ctrl
p1745[0...2] Flux variance limit in stall / Flux var.lim.stall
p1750[0...2] Control word of motor model / Motor model CtrlWd
p1752[0...2] Start-freq. speed adaption (VC with encoder) / Start-freq. (VC)
p1755[0...2] Start-freq. motor model (SLVC) / Start-freq. (SLVC)
p1756[0...2] Hyst.-freq. motor model (SLVC) / Hyst. freq. (SLVC)
p1758[0...2] T(wait) transit to open-loop / T(wait) trans.->OL
p1759[0...2] T(wait) transit to closed-loop / T(wait) trans.->CL
p1764[0...2] Kp of n-adaption (SLVC) / Kp n-adapt. (SLVC)
p1767[0...2] Tn of n-adaption (SLVC) / Tn n-adapt. (SLVC)
p1780[0...2] Control word of Rs/Rr-adaption / CtrlWd Rs/Rr adapt
p1781[0...2] Tn of Rs-adaption / Tn of Rs-adaption
p1786[0...2] Tn of Xm-adaption / Tn of Xm-adaption
p1800[0...2] Pulse frequency / Pulse frequency
p1803[0...2] Max. modulation / Max. modulation
p1820[0...2] Reverse output phase sequence / Rev.outp.phase seq
p1909[0...2] Ctrl. word of motor data ident. / Ctrl.mot.data id.
p2000[0...2] Reference frequency / Reference freq.
p2001[0...2] Reference voltage / Reference voltage
p2002[0...2] Reference current / Reference current
p2003[0...2] Reference torque / Reference torque
p2004[0...2] Reference power / Reference power
p2150[0...2] Hysteresis frequency f_hys / Hyst. freq. f_hys
p2151[0...2] CI: Speed setpoint for messages / n-Set for msg
p2152[0...2] Delay time of f>fmax / Delay f>fmax
p2153[0...2] Time-constant speed filter / Tconst. speed filt
p2155[0...2] Threshold frequency f_1 / Threshold freq f_1
p2156[0...2] Delay time of threshold freq f_1 / Delay time of f_1
p2157[0...2] Threshold frequency f_2 / Threshold freq f_2
p2158[0...2] Delay time of threshold freq f_2 / Delay time of f_2
p2159[0...2] Threshold frequency f_3 / Threshold freq f_3
p2160[0...2] Delay time of threshold freq f_3 / Delay time of f_3
p2161[0...2] Min. threshold for freq. setp. / Setp.min.threshold
p2162[0...2] Hysteresis freq. for overspeed / Overspd. hyst.freq
p2162[0...2] Hysteresis freq. for overspeed / Overspd. hyst.freq
p2163[0...2] Entry freq. for perm. deviation / Entry freq. deviat
p2164[0...2] Hysteresis frequency deviation / Hyster freq deviat
p2165[0...2] Delay time permitted deviation / Delay_T perm. dev.
p2166[0...2] Delay time ramp up completed / Delay_T rampUpCmpl
p2167[0...2] Switch-off frequency f_off / SwOff freq. f_off
p2168[0...2] Delay time T_off / Delay time T_off
To Next Page
Loading...
Need help?
General
