Tektronix DSA70000/B Series

Commands Listed in Alphabetical Order
MASK? (Query O
nly)
This q uery-only command returns the states of all settable mask parameters.
Group
Mask
Syntax
MASK?
Examples
MASK? might return the following response: :MASK:FILTER 0;AUTOADJUST
0;AUTOADJUST:HDELTA 10;VDELTA 10;:MASK:AUTOSET:AUTOADJUST
1;HPOS 1;HSCALE 1;MODE MANUAL;OFFSETADJ 1;TRIGGER 1;VPOS
1;VSCALE 1;STANDARD NO NE;USER:ONE 0.0000;ZERO 0.0000;TYPE
NORMALIZED;:MASK:SOURCE CH1;COUNT:FAILURE S 0;HITS 0;S EG1:
3A 4D 41 53 4B 3A 46 49 4C 54 45 52 20 30 3B 41 55 54 4F 41
44 4A 55 53 54 20 30 3B 41 55 54 4F 41 44 4A 55 53 54 3A
48 44 45 4C 54 41 20 31 30 3B 56 44 45 4C 54 41 20 31 30
3B 3A 4D 41 53 4B 3A 41 55 54 4F 53 45 54 3A 41 55 54 4F
41 44 4A 55 53 54 20 31 3B 48 50 4F 53 20 31 3B 48 53 43
41 4C 45 20 31 3B 4D 4F 44 45 20 4D 41 4E 55 41 4C 3B 4F
46 46 53 45 54 41 44 4A 20 31 3B 54 52 49 47 47 45 52 20
31 3B 56 50 4F 53 20 31 3B 56 53 43 41 4C 45 20 31 3B 53
54 41 4E 44 41 52 44 20 4E 4F 4E 45 3B 55 53 45 52 3A 4F
4E 45 20 30 2E 30 30 30 30 3B 5A 45 52 4F 20 30 2E 30 30
30 30 3B 54 59 50 45 20 4E 4F 52 4D 41 4C 49 5A 45 44 3B
3A 4D 41 53 4B 3A 53 4F 55 52 43 45 20 43 48 31 3B 43 4F
55 4E 54 3A 46 41 49 4C 55 52 45 53 20 30 3B 48 49 54 53
20 30 3B 53 45 47 31 3A mask? :MASK:FI LTER 0;AUTOADJUST
0;AUTOADJUST:HDELTA 10;VDELTA 10;:MASK:AUTOSET:AUTOADJUST
1;HPOS 1;HSCALE 1;MODE MANUAL;OFFSETADJ 1;TRIGGER 1;VPOS
1;VSCALE 1;STANDARD NO NE;USER:ONE 0.0000;ZERO 0.0000;TYPE
NORMALIZED;:MASK:SOURCE CH1;COUNT:FAILURE S 0;HITS 0
.
MASK:AUTOAdjust
This command optimizes or queries the signal position within the mask to
minimize hits. It sets a mode so that the
MASK:SOURCE waveform is compared
against the mask and is shifted up, down, left, or right to minimize the hits.
Group
Mask
Syntax
MASK:AUTOAdjust {ON|OFF|<NR1>}
MASK:AUTOAdjust?
2-286 DPO7000, DPO70000/B and DSA7000/B Series Programmer Manual